Answered: 1) The simply supported beam with the…

1) The simply supported beam with the cross-section as shown in the figure supports the loads as shown. Determine the thickness t if the flexural stress in the beam is not to exceed 100 MPa.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 17. A rectangular bar is loaded as shown. Find the maximum tensile stress developed ove section A-A.…

A: Given : Max. tensile stress developed over section A-A ?

Q: maximum value for the load R.

Q: For the truss shown, calo member BD. The cross-se member is 1200mm². A 6m C 4m E

Q: Consider the beam below. If the beam is subject to a 20kN internal shear force, determine the…

A: shear force , V= 20 KN thickness of all pieces= 30 mm

Q: Determine the shear stress on the a-a plane. 45 MPa 30° a (а) -10.5 МРа (b) 10.5 MPа (c) -50.3 МРа…

A: Shear stress on plane a-a is given by ζxy'=σy-σx2sin2θ+ζxycos2θwhere θ=angle of inclination of…

Q: 400 Material A 300 Material B 200 Material A 100 0.002 0.004 0.006

A: Solution: B) Given Data: Tensile load=88 kNElastic modulus of material A=150 GPaElastic modulus of…

Q: What is the stress at the section x - x. for the bar ABCD with uniform cross-section 1000 mm²? с A…

Q: W16

Q: At a point in beam, the principal stresses are 100 N/mm² and 50 N/mm². The stress in x-direction is…

A: Given - The principle stresses are, σ1 = 100 N/mm2 σ2 = 50 N/mm2 The stress in x-direction, σx = 65…

Q: PROBLEM 4: Find the elongation in a 2m long steel bar by subjecting it to 40 MPa stress. E = 200 GPa…

A: Given- Length of the steel rod (L) = 2m = 2000mm Stress in steel rod (σ) = 40MPa E= 200GPa=…

Q: Rigid bar ABCD is loaded and supported as shown. Steel [E = 30000 ksi] bars (1) and (2) are…

Q: A beam with a T-section is supported and loaded as shown in the figure. The cross section has width…

A: A beam with the T section is given in the question all the loading condition is given in the above…

Q: Q1) Three bars AB, CD and ED are used to support ACE beam. The three bares have modulus of…

A: Draw the free body diagram. Equilibrium of vertical forces,…

Q: The belt shown has a width of 43 mm and a thickness of 6 mm. [P1= 30 kN, P2= 6 kN, P3= 14 kN, P4= 14…

A: the width of the belt (b)=43 mm, thickness (t)=6 mm.P1=30 kN, P2=6 kN, P3=14 kN, P4=14 kN.…

Q: 8. A steel bar of 40mm x 40mm square cross-section is subjected to an axial compressive load of…

Q: Problem # 1: For the truss loaded as shown, calculate the axial stress developed in members CD, ND…

Q: SkN 20KN 10KN 10kN/m 0,2*b 0,2*b 10kNm 0,8 b by 1m 3m 4m 2m 1m 2m

A: Given data: yield strength =400 MPa Factor of safety =2

Q: Read the question carefully. Give me right solution according to the question. Find the load P in…

A: given data:- yield stress due to bending=250 mpaelastic constant E =200000 moamoment of inertia of…

Q: The rigid beam is supported by the two bars shown in a horizontal position before the load P is…

Q: For the state stress shown in figure below, determine the principle stresses and the maximum…

Q: 3. Strength value is amount of stress at 4. Point- Load Index (Is) ---- ------ %3D ---

A: Stress is a tensor quantity, which is the internal resistance offered to oppose the deformations.

Q: A beam is supported as shown, and its cross-section is rectangular with a=5 cm and w= 2 cm. What is…

A: Solution Given Data a= 5 cm w= 2 cm

Q: The beam is loaded by two point forces P. The beam is assembled according to the cross-sectional…

A: Dimension of beam:Upper plank = 25 mm×260 mmVertical plank = 220 mm×50 mmLongitudnal direction of…

Q: arning Goal: me member shown is subjected to a compressive ress in the x direction of a = 400 ksi…

Q: A simple pin-connected truss is loaded and supported as shown. The load P is 160 kN. All members of…

A: Solution: Given: Load, P = 160 kN outside diameter = 130 mm Wall Thickness = 9 mm

Q: hat have an outside diameter of 135 mm and a wall thickness of 9 mm. Determine the normal stress in…

A: From a given question it is required to calculate stresses in each member of truss.

Q: Consider a case where a place where a plate is subjected to combined loading, including pressure q…

Q: For the cantilever beam shown. find the value of Normal stress due to axial load at :point F 10 m 4…

A: Normal stress is the stress which get generated due to the force acting on normal or perpendicular…

Q: SIMPLE STRESSES 340 mm 3. Two plates are connected by bolts as shown in the figure. Compute the…

A: Force will be minimum of shear strength of bolts and axial strength of Plate

Q: Question #4 For the cantilever beam shown in Figure 4, a) Determine the maximum shear stress on the…

A: Given data Point load Length Cantilever beam Cross section Web thickness Flange thickness

Q: Consider the beam below. If the beam is subject to a 20kN internal shear force, determine the…

A: Given:- V= 20 KN thickness of all pieces= 30 mm To find:- The maximum shear stress

Q: Which of the following does not cause any changes in the value of bending stress on a beam?

A: Which of the following does not change any value in bending stress in beam- (D)- Load acting on the…

Concept explainers

Composite Construction

Composite construction is the construction of structures in which two or more materials are used. Regarding structural engineering, composite construction is a construction where two materials are bound together in a technical manner such that both the materials act as a single unit to carry and transfer the load. The motives of composite construction are to increase the structural strength, make structures more aesthetic, and provide a sustainable environment.

Question

Instructions: Solve the following problems as instructed. Boxed final answers
and round off to the nearest two decimal places. Show your solutions. No
solutions wrong.
1) The simply supported beam with the cross-section as shown in the
figure supports the loads as shown. Determine the thickness t if the
flexural stress in the beam is not to exceed 100 MPa.
60 kN
200mm
30 kN
-0.40m
300mm
B
C
200mm
1.50m
H
1.50m
1.00m
D

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

E3
P1=50kN P2=80kN
A so-called "trapeze bar" in a hospital room provides a means for patients to exercise while in bed (see figure). The bar is 2.3 m long and has a cross section in the shape of a regular octagon. The design load is 1.4 kN applied at the midpoint of the bar, and the allowable bending stress is 180 MPa. Determine the minimum height h of the bar. Round to one decimal place. (Assume that the ends of the bar are simply supported and that the weight of the bar is negligible.) hmin mm
Rigid bar ABCD is loaded and supported as shown. Steel [E = 28500 ksi] bars (1) and (2) are unstressed before the load P is applied. Bar (1) has a cross-sectional area of 0.62 in.² and bar (2) has a cross-sectional area of 0.38 in.². After load P is applied, the strain in bar (1) is found to be 670 μe. Assume L₁=68 in., L₂=94 in., a-35 in., b=39 in., and c-22 in. Determine: (a) the stresses in bars (1) and (2). (b) the vertical deflection vp of point D on the rigid bar. (c) the load P. (2) (1) L₁ B C a L2 b C D P
A 200 MPa shear stress is applied on along CD. Calculate diagonal strain along AC. Given modulus of elasticity is 120 GPa and Poisson's ratio is 0.2. 200 MPa A B Diagonal strain will be in the form of k x 10-3 Find 'k'
Derive the Bending Stress Formula
A 31 mm diameter bronze bar 3.7 m long is placed between two rigid walls. At a temperature of -39°C, the gap A = 2.3 mm. Find the temperature(at degree-Celsius) at which the compressive stress in the bar will be 40 MPa. Use a = 19.84 x 106 m/(m-°C) and E = 82 GPa. Answer in two decimal places. Numerical values only. Don't indicate units here, just on the submitted solution.
1. Establish stress equations for both bars in the two-bar assembly shown below which isloaded with force P, and constrained at the two ends, as shown in the figure.
Rigid bar ABCD is loaded and supported as shown. Steel [E = 28400 ksi] bars (1) and (2) are unstressed before the load P is applied. Bar (1) has a cross-sectional area of 0.82 in.² and bar (2) has a cross-sectional area of 0.41 in.². After load P is applied, the strain in bar (1) is found to be 700 μe. Assume L₁=69 in., L₂-89 in., a=34 in., b=33 in., and c-37 in. Determine: (a) the stresses in bars (1) and (2). (b) the vertical deflection VD of point D on the rigid bar. (c) the load P. A Answers: (a) 0₁ = (b) VD = (c) P= i i i L₁ a (1) B L2 b ksi, 0₂ = in. kips. (2) C i D P ksi.
Using the CREMONA method, determine the forces and types of stress in the bars and analyze them.
SIR, SOLVE THE QUESTION PROPER AND CORRECTLY. THANKS.
Need answer fast.