1) The correct plot between temperature and distance in the solid-liquid interface (solidification front) based on actual and equilibrium temperature gradients (G) for the formation of equiaxed dendritic structure will be Actual G Temperature Temperature Equiblirium G Distance from interface Actual G/ Actual G/ Actual G Temperature Temperature Equiblirium G Equiblirium G Equiblirium G Distance from interface Distance from interface Distance from interface - II IV

Q: 75 mm When a force P of 750 N is applied to the pedal shown in the figure, find the diameter (mm) of…

A: Given data: The applied force, P = 750 N. The shear stress in the pin, τ = 40 MPa. Draw the…

Q: LESSON: AUTODESK AUTOCAD Choose from the choices:

A: The broken line is used to draw the large drawings which are not possible to draw on the sheet,…

Q: 00 0 021 0 043 0 25 0 1280

A:

Q: Convert to isometric drawing mark point A as the lowest point

A: use a 30-60 triangle to create the isometric  figure ng follow the left, front and top illustration…

Q: 5.) A kilogram of wet steam is taken as a sample for study. It has a pressure of 0.805 MPa and an…

A: As per the Bartleby guidelines, We are subjected to solve only one question at a time. Please repost…

Q: Given the following data, draw in a cartesian plane, the resulting vector,and it's three director…

A:

Q: Consider the following linear equations -7x + 8y + 4z - 7x + (25 – k)y + 3z = 11 - 7x + 8y + (7 –…

A: The given set of equations are:

Q: where are the graphs?

A: Given data in the related question: Maximum speed = vf = 183.58 mi/hr Distance travelled = 5 mi Time…

Q: The front and top views are given. Use this to create the missing side view. Note the front view is…

A: The required missing side view for A and B and the missing lines for C are drawn below.

Q: Two views of a hexagonal cylinder are shown in Figure 3. Dimensions given are in mm. Use your…

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: Identify the basic drawing, using the cartesian coordinates ( Absolute and Incremental ) write the…

A: Write the precise location co-ordinates for each point by using Absolute co-ordinate system.

Q: Directions: Draw an isometric view of the following orthographic views. Views most be properly…

A: Draw an isometric view of the following orthographic views.Views most be properly aligned attached.…

Q: Do four colors really suffice? Suppose this map shows the provinces of a country. peculiarity of…

A: The four colour theorem, also known as the four colour map theorem, claims that no more than…

Q: 2. For the plan area shown, determine the location of the Centriod. Use you're the last two digits…

A:

Q: Given the top view and right side view, draw the sectional view of the figure. Please include the…

A: Find Sectional View of the given figure

Q: Given the left and front views, sketch the top view.

A: The problem is easily done with the help of orthogonal projection. first try to imagine the 3D view…

Q: Can you draw the OBLIQUE SECTION VIEW of this figure?

A:

Q: Draft and annotate the 2D sketch of upright using AutoCAD and mention all the dimensions. Colour the…

A:

Q: Draw the top view, side view, and front view of the figure below.

A: The required Front view , Top view and Side are drawn using third angle method of projection.

Q: Consider FIG-DD in the appendix.   Note: For Blocks “A” & “B” & “C”: The mass of “A” is 30 kg.…

A:

Q: Based on Figure 3: draw the section view along the x-x cutting plane line.  i) Complete the section…

A: Please refer the following image for required sectional view of the given object. 1 Grid = 1 Unit

Q: n the figure, front (1st picture) and left (2nd picture) views of a machine part are given. Based on…

A: Isometric projection Isometric projection is a method for representing three-dimensional objects…

Q: In the following diagram, which lines are indicated by D? Ø20.00 60.00 A Select one: E B A.…

A: To find : which lines are indicated by D

Q: Draw the isometric projection of the object showing the top, front and right side.

A:

Q: Draw the plan, Front view and the Side view of the following figure and do the dimensioning.

A: Please refer the following orthographic views of the given object.

Q: Draw the three projections accurately on paper: the top, front, and side, with the side projection…

A: Top View       +-----------+       |           |       |           |       |           |…

Q: Draw the following views in Orthographic Third Angle Projection. 10:35 am 20 80 20 10:35 am

A: Given Data: Isometric view of the figure

Q: Q1: Use scale (1:1), draw the front, top & side views of shape shown below. (50 M)

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: If a cutting plane cuts the given objects in to given position as shown in figure.reproduced the…

A:

Q: Draw the one-point perspective of the object. The station point is 60 mm away from the picture plane…

A:

Q: PLease draw the top view and section view with dimension of the figure

A: Here is Top View and Section View of figure with well dimensioned.

Q: Draw by using free hand sketch to find Front, Side and Top views of the following shape

A: Refer the following image for the the free hand sketch  for Front, Side and Top view of the given…

Q: 2 views are given (front and top), left view is requested. You also need to dimension the drawings.…

A: according to the given details in the question. left side view given below

Q: o. Can you draw the ALIGNED SECTION VIEW and the OBLIQUE SECTION VIEW of this figure? I don't need a…

A:

Q: 20 30 40. -30 100- Draw the three projections of the following figure 60

A: