1) Steam boiler is to generate saturated steam at 800 kPa abs from water at 70 C. Flue gas from bunker fuel-fired furnace is available at temperature of 1100 C. Final temperature of flue gas leaving the boiler is 275 C, what is the LMTD?

1) Steam boiler is to generate saturated steam at 800 kPa abs from water at 70 C. Flue gas from bunker fuel-fired furnace is available at temperature of 1100 C. Final temperature of flue gas leaving the boiler is 275 C, what is the LMTD?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q3) Compare between steam infusion and steam injection heat exchangers ?
Please find the highest thermal efficiency possible, while remaining within the boundaries. What is required: -Power produced must be at least 60 Mega Watts -Thermal efficiency must be greater than 36% -Back-work ratio must be smaller than 48% Assume: -air is the working fluid -specific heats vary with temperature (use table A-17) -Compressor inlet is at 1atm and 300k -the combustion process is isobaric and is modeled as a heat exchanger -Turbine exhaust is the same pressure as compressor inlet Compressor specifics: -Max volume flow rate (m^3/h) = 600,000 -Max outlet pressure (atm) = 12 -Isentropic efficiency = 90% Combustion chamber and gas tubine specifics (Note these come as a set) -Max pressure = 16.7 atm -Max temp = 1500 (celcius) -Turbine isentropic efficiency = 92% -Max heat rate = 230MW
Step 2) Find the optimurn value of the reheat pressure in order to achieve the highest efficiency in the domain of the admissible values of the steam quality. For that keep the turbine infet conditions as given. Cycle 2- Idcal Rankine Cycle With Reheating Pick out four different values of the reheat pressure within the interval (0.1 to 0.4) x inlet pressure to high pressure turbine, to find the proper reheat pressure. Procced as follows: Case I. Keep the turbine exit pressure the same as the one obtained in step 1 for the highest efficieney at x= 0.87. Change the reheat pressure to obtain the best efficiency. Casc II. Keep the reheat pressure obtained in Case I fixed and change the turbine exit pressure to obtain efficiercy corresponding to x = 0.87 TEM_1 ITEM 1 CONT KW PSI 5 35 190,000 1700
Question 2 A 1-1 shell & tube exchange is with Sulfuric Acid flowing at 115 gpm, at 80.33 F (Cp=.02 Btu/lbm-F) (SG=1.8), to cool 70 gpm of water from 175 F to 100 F in a counter-current mode. A) Assign shell side fluid. Explain your decision. B) What is the total hot side heat duty? C) Calculate LMTD D) What is the value of Ft and what does it mean? E) Assume a "typical heat transfer coefficient" conservatively, estimate the exchanger area in Ft²?
Airborne heat used to heat a homerefrigerant circulating in the cycle of the pump-134a600 kPa pressure and 40 oC enter the condenser, at the same pressureIt comes out as a saturated liquid. Circulating refrigerantthe mass flow of the fluid is 0.03 kg / s and the compressor hasif the power is 1.8 kWa) COP value of the heat pumpb) Airborne per unit time ?̇ ?Find the amount of heat.
1. Steam is generated at 4.20 MPa and 460°C and condensation occurs at 0.105MP.. a. For a rankine engine operating between these limits compute the thermal efficiency and the heat rate. b. Considering that a Rankine cycle occurs between the same limits, determine Q.. Q,, w. and e C. What mass flow rate is required for a net output of 35,000 kW?
The condensing pressure for a Rankine engine is 0.001325 MPavac. Calculate the following for steam flow rate = 16.3846 kg/sec of steam when the steam at the beginning of expansion is at 119.6 deg SH and 4.0 Mpaa. Draw the TS and equipment diagrams for the ideal and actual case and find for the following for the ideal case: Combined work (KW) . Ans.____________________________ Combined steam rate in kg/KW-hr. Ans.___________________________ Actual heat rate( KJ/KW-hr). Ans.____________________________
a steam 8.0 mpa and 485 degrees celsius enter the turbine and expand at condenser pressure of 0.006 mpa for cycle and 1kg of steam. determine heat added, worknet, thermal efficienc, for the engine determine steam flow for an engine output of 40000 kw, work turbine, energy chargable, ideal heat rate
Detailed explanation: Two AES exchangers in series have trouble heating up a process stream from 50ᵒC to 90ᵒC, and cooling down a hot stream with the same flow rate from 110ᵒC to 70ᵒC. Luckily, there is an abandoned AES exchanger available that has four times the surface of the two existing exchangers, and even better, it has the right material and sufficiently high design P & T, and would fit on the plot space occupied by the existing exchangers. Is replacement a good idea?
02. The Li-Br water absorption cycle with heat exchanger between absorber and generator operate at the following temperature: generator temperature = 100°C, condenser temperature = 34°C, evaporator temperature=10°C, absorber temperature solution leaving heat exchanger to generator is 52°C. The flow rate of solution delivered by the pump is 0.6 kg/s. Is there a danger of crystallization? 30°C, and the temperature of %3D
Power generation using steam is one of the most common method which can be found around the world. In these type of power plants, steam goes through a basic thermodynamic cycle called Rankine cycle which is shown in the following figure. Steam flow Boiler Qin Pump Wout Win Condenser For the proper operation of the cycle, water should be pumped to the boiler using pump which required work input (Wn) to the cycle. Heat energy should be supplied to the boiler (Qin) to generate steam and then high pressure steam is fed to the turbine. By extracting the energy from high pressure steam, turbine is producing work output (Wout)- Because of this, the steam pressure is reduced and low pressure steam is flowing into the condenser. Condenser removes heat energy from steam further (Qout) and steam is converted into liquid water. The liquid water can be pumped into the boiler again and the cycle continues. Performance of a Ranking cycle can be evaluated by using thermal efficiency (neh)which is…
The condensing pressure for a Rankine engine is 0.001325 MPavac. Calculate the following for steam flow rate = 1 kg/sec of steam when the steam at the beginning of expansion is at 119.6 deg SH and 4.0 Mpaa. Draw the TS and equipment diagrams for the ideal and actual case and find for the following for the ideal case: Ideal turbine work (KW). Ans.____________________________ Heat rejected at condenser (KJ/sec). Ans.____________________________ Mass of cooling water in kg/sec if cp H2O = 4.18 KJ/kg-K, and inlet temp of water to condenser = 20 deg C, outlet temp is 35 deg C. Ans.____________________________ Pump work in KW. Ans.___________________________