1) For the expression f(A,B,C) = P0 + P5 + P6 + P7 , set the output in terms of one of the inputs and design a 2x4 multiplexer. (Hint: Use a truth table) 2) Design a combinational circuit using full adders to multiply a 4-bit unsigned number by 2. Draw a logic diagram using the block diagram of full adder as the building block.

1) For the expression f(A,B,C) = P0 + P5 + P6 + P7 , set the output in terms of one of the inputs and design a 2x4 multiplexer. (Hint: Use a truth table) 2) Design a combinational circuit using full adders to multiply a 4-bit unsigned number by 2. Draw a logic diagram using the block diagram of full adder as the building block.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

An X-input exclusive-OR gate and a Y-input exclusive-OR gate (where X=3, Y=4 have their outputs connected to a 2-input exclusive-NORgate. Do the following:a) Draw the logic diagram and analyze the logic expression of the output (in standard SOPform).b) List out all essential prime implicants.
Design the following combinational logic circuit with a four-bit input and a three-bit output. The input represents two unsigned 2-bit numbers: A1 A0 and B1 B0. The output C2 C1.C0 is the result of the integer binary division A1 A0/B1 B0 rounded down to three bits. The 3-bit output has a 2-bit unsigned whole part C2 C1 and a fraction part CO. The weight of the fraction bit CO is 21. Note the quotient should be rounded down, i.e. the division 01/11 should give the outputs 00.0 (1/3 rounded down to 0) not 00.1 (1/3 rounded up to 0.5). A result of infinity should be represented as 11.1. A minimal logic implementation is not required. (Hint: start by producing a truth table of your design).
In this assignment, you are required to design a circuit that counts and displays the sequence of the number 010430011092 . The number will then be displayed on a 7-segment display and changed every 1 second. The block diagram is as shown in Figure 1. Construct your design as follow: - (a) Design a combinational logic circuit that converts binary number to a sequence of the number 010430011092 and to be displayed on a single common anode 7-segment display. The logic circuit must be designed using 2-input NAND gate
Design a 3-bit counter that counts the following sequence: 7,5, 3. 1.0.7, 5. 3, 1, 0, 7. etc. Using the sequential design technique that starts from a state diagram, draw the state table. minimize the logic. and draw the final circuit. The outputs of logic circuit are 2 = Qo Q1. I, = Qo.Qi + Qo.Qi, Io = Qo.Q2, Cont2 = Qj Q2 Cont1 = Qu Q2. Cont0 = Q2 Qo.Q1. h = Qo.Qi + Qo.Q1, Io = Qo Qz Cont2 = Q, Q2 Contl = Qo Q2 Cont0 = Q2 Qo Qı Ij = Qo.Q, + Q».Qı, Io = Qo. Q2. Cont2 = Qj Q2. Contl = Qo.Q2. Cont) = Q2 L = Qo.Qı. I¡ = Q. Qj + Qu Q Io = Qv.Qz Comt2 = Q, Q, Contl = Q Q2 Cont0 = Q2 !! fefsto How much will be per-product cost and th
Design a logic circuit with four inputs and one output that will produce "l" in the output only if the input patterns have odd number of zeros. a) Write the Boolean equation for the circuit in the simplest SOP form. b) Draw the logic circuit for the above equation in its simplest form. c) Re Design the logic circuit using NANI) gates only?
1. Design a combinational logic circuit that compares two 4-bit numbers A and B. The circuit should output the relation of the two inputs. Use an available TTL IC for the design.
We want to design a circuit to detect prime numbers.The input of the circuit is a 4-bit binary number and the output is a single bit and should show one when the number is prime and zero otherwise.B. Implement the circuit using a 4× 1 multiplexer and combinational logic gates.C. Implement the circuit using only one decoder and one OR gate. What is the size of the decoder you use?
2.1 Combinational logic circuits. Tabulates a truth table for the following Boolean expression shown in Equation 1.1. f = A.B.C + A.B.C + A.B.C (1.1) 2.2 Half adder. A half adder is a circuit that adds two binary digits, A and B. It has two outputs, sum (S) and carry (C). The carry signal represents an overflow into the next digit of a multi-digit addition. Figure 1.2 depicted a logic diagram for a half adder. a. derives the Boolean expression for s and c. b. tabulates a truth table for the half adder. Ao Bo Figure 1.2: Half adder os S C
Electrical Engineering Task Figure shows a BCD counter that produces a four-bit output representing the BCD code for number of pulses that have been applied to the counter input. In particular, the DCBA outputs will never represent a number greater than 1001,-91, (MOD-10). (MSB) Logic BCD counter circuit HIGH only when DCBA=210-310, or 910 a. Draw the logic circuit using the minimum expression and then explain its operation. B
a) Design a combinational circuit that would take a 3-bit binary number and generate an output if the input value in decimal is either divisible by 2 or 3. iii) Explain and show how you would implement this circuit using a 4-to-1 Multiplexer and other appropriate logic gates. Use a block diagram for the multiplexer.
Consider two 8-bit inputs, A = $52 and B = $C3 to the arithmetic and logic unit (ALU). Compute R =A + B. Express R in the hexadecimal form $-- : -61 Express N-Z-V-C bits in the form ----:
We want to perform subtraction operation in which we need a full subtractor. First draw Truth table for full subtractor. Due to pandemic you are unable to get the desire component. but you have only eight- to-one multiplexers with you. What do you think, can you still perform subtraction operation with multiplexer or not? If yes, draw the logic circuit.