1- Draw a simple sketch, then show its processes on the (T-s) diagram for each ideal cycle listed in the table below. Cycle Туре Steam Condition Closed FWH Direct Contact Turbine inlet Reheat Outlet Condenser Drain Drain FWH Cascaded Pumped Backward Forward A Reheat 100 bar, 60 bar, 410 C° 0.07 bar 410 C°

1- Draw a simple sketch, then show its processes on the (T-s) diagram for each ideal cycle listed in the table below. Cycle Туре Steam Condition Closed FWH Direct Contact Turbine inlet Reheat Outlet Condenser Drain Drain FWH Cascaded Pumped Backward Forward A Reheat 100 bar, 60 bar, 410 C° 0.07 bar 410 C°

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I'll leave a thumbs up if you ans the following. Determine the following: a. The fuel flow rate in kg/sec b. Cooling water flow rate in kg/min c. Assume an ideal cycle with pump efficiency = 80% and turbine efficiency = 85%, find the quality of steam entering the condenser
What is the cycle efficency?
Instructions: Perform a cycle analysis for the given reheat-regenerative Rankine cycles. Supply the table with the necessary equations based on enthalpy and mass fraction of working fluid’s state points.
Thermodynamics Instructions: Please Answer the letter (a) to (d) in the problem. *show complete solutions and please write legibly. TY
Multiple Choice. Choose the correct answer and show COMPLETEsolution. (Diesel cycle)
贪411 461l1 zain IQ Asiacell M Superheating process .8 should exists for protecting the сycle. none of these answers. should not exist in the cycle to keep it working efficiently. is necessary to keep the refrigerant at low temperature. The refrigerant leaving the .7 compressor follows an isentropic process. an isothermal process. an adiabatic process an isotropic process. All specific physical quantities are .5 measured relative to
A piston engine operating on the Carnot cycle uses air as the working fluid. At the start of isothermal expansion air is 521 psi & 1100°F. Isothermal Expansion ratio = 1.25. Isentropic Compression ratio = 3.2. The amount of air circulated is 15 Ibm/min. Draw and label the P-V and T-S diagram. Determine the following; a.) Temperature of the sink, °F b.) The Carnot cycle efficiency, in % c.) Power output, Hp d.) Mean effective pressure, psi
Thermodynamics,please can you solve it
solve 2 draw schematic diagram
2) Determine the Ranking Cycle Efficiency in %. 3) Determine the Brake Thermal Efficiency of the cycle in % 4) Determine the Combined thermal and electrical efficiency in %.
34
Part 2: Problem Statement A gas turbine power plant operates on simple and ideal cycle with air as the working fluid. The pressure ratio is rp = 10, compressor inlet temperature is T₁ = 300 K and turbine inlet temperature is T3 Use constant specific heat cp = 1.005K and Kair = 1.4 kg.K • Create a new sheet and name it "solution 1" • Create a table for T3 from 800 to 1200 with increment of AT 50 K • Calculate compressor and turbine exit temperatures T₂ = T₁(₂)(k-1)/k (k-1)/k T4 = T3 • (-/-) Calculate compressor work Wc, turbine work WT and heat addition occ • Calculate system efficiency 7th Energy output WT - Wc Energy Input Qcc • Create a scatter chart for T3 VS nth 1) Add chart title 2) Add axis title and show units 3) Add a proper trendline and show equation • What is the system efficiency when turbine inlet temperatures are 920 and 1140 K • Create a new sheet and name it "solution 2" • Repeat all steps for pressure ratio of r₂ = 14