1) calculate the reaction forces  2) Calculate and draw the Bending moment digram, and what is the value of maximium bending moment ? 3) calculate and draw the shear force digram and what is the value of the maximum shear force ?

Q: 1.Determine the maximum compressive stress acting on the cross section. 2.Determine the maximum…

A:

Q: 184 What is the strain energy of the massless stepped bar as shown in the figure below? [Take E= 200…

A: Strain energy of the massless stepped bar Take E=200Gpa

Q: The cast iron beam in the figure has an overhang of length b = 2 m at each end. The bending working…

A: Assumption: Material is isotropic, homogeneous, and elastic in which hooks law is valid.  The plane…

Q: In the figure below, at section n-n (x = 4m from point A) determine shearing stress at a on the…

A:

Q: Let strain rosette shown in figure computed the values of strains at the built in end and in NA of…

A:

Q: Pa. Determine the magnitude of the angle of twist in a

A:

Q: A cylindrical rod AB has a length ? = 80 cm and a diameter of ? = 2 cm. The modulus of elasticity is…

A: Given Length of Rod, L=80cm Diameter of rod=2 cm Modulus of elasticity, E=200 GPa Force, P=100 kN…

Q: A hollow steel shaft with an outside diameter of 75 mm and a wall thickness of 5 mm is subjected to…

A: Given data in question  Torque 2410 Nm Outside Diameter D0 75 mm Thickness 5 mm Shear modulus 80 GPa…

Q: f the bending stress at section 2-20 MPa. What are the bending stresses at sections 1, 3, and 12 mm…

A:

Q: (MPa), 022=b+c+d+h (MPa), t12=c+g+h+d (MPa), O°=2(T1), E= 1000(T1) Mpa, v=(T1)/100 a) Calculate…

A:

Q: A rod having a circular cross section (radius; 0.5 in, height; 15 in) is subjected to loadings as in…

A: torque at fixed end  T=540 lb.indiameter of shaft  d=0.5 inthen shear stress at  A abd B…

Q: 50mm a biaxial load that results in B C Given: A “happy-little-cube" of material is subject O = 150…

A:

Q: 100 mm 25 mm 125 mm M. 75 mm The beam is subjected to an internal moment of M = 3 kNm. 25 mm 75 mm…

A:

Q: The cross section of a wood beam carries a bending moment M of magnitude 20R lb.-in. acting at 10⁰…

A:

Q: The stress on a structure is as follows. The EI of the ?-shaped part of the structural section is…

A:

Q: 1. A T-section beam that is subjected to a concentrated and a distributed load can be identified in…

A:

Q: 200 mm If the beam is subjected to a bending moment of M=50KN, determine the maximum bending stress…

A: Using formula to find bending stress

Q: Problem 5.9 A solid steel bar has a cross section of side b and is supported as shown. Knowing that…

A: To Determine Depth of the beam, b

Q: What is the strain energy of the massless stepped bar as shown in the figure below? Take E= 200 GPa]…

A: GIVEN:

Q: The z-component of moment M will cause compression at A and B, and tension at C and D. The…

A:

Q: The shear force Ty acts on the section in the y direction. Calculate the shear force Tythat the…

A:

Q: Displacement d.o.f. d; at ends of a uniform bar element have the directions shown. Write an…

A: Derivation of the element stiffness matrix for a bar element using the principle of minimum…

Q: The stresses shown in the figure act at a point in a stressed body. Determine the normal and shear…

A: Given: Sx=7200 psi Sy=2300 psi  θ=64o  To find: Normal and shear stresses

Q: A hollow steel shaft with an outside diameter of 75 mm and a wall thickness of 5 mm is subjected to…

A: Given Outside diameter (Do) = 75mm Thickness of wall (T) = 5mm Torque (T) = 1680 N-m Shear modulus…

Q: The stresses shown in the figure act at a point on the free surface of a machine component. If o =…

A:

Q: 10 k Sectian 300 800 ISM P= 300 ku, e = 250mn From the given figure shown, Calculate the stress at…

A:

Q: The differential element above represents the state of plane stress at a pont J steel beam. Which of…

A: Given data: σX=60 ksiσY=-20 ksiζXY=40 ksi

Q: 3 k= 4000 N/m 4

A:

Q: The beam shown is hinged at one end. It is supported by two steel rods of equal length of 1.5m.…

A:

Q: The structure shown is supported by a steel rod at B. Specifications of the steel rod L= 2m…

A: Data given: Specifications of the steel rod L= 2m d=25 mm E=200 GPa Asked: 1. Draw the shear force…

Members with compression and bending

Compression members are structural elements that carry compressive axial force. They are the vertical members of a building that support beams and their design, which is governed by buckling and strength. Columns are known as struct or compression members, which are subjected to compressive forces. These members provide stiffness to the building and avoid any imperfection regarding the transfer of axial load. For instance, webs in a truss, braces in a framed structure, tiers, and so on.