1- A simply supported beam is composed of three plates, which are fastened together using bolts that are spaced at 150mm intervals in the longitudinal direction of the beam. If the allowable shear on the bolts is 15 kN, what is the maximum allowable value of the applied load P? 24 24 Bolts spaced at 150 mm P 70 AB longitudinall - 1.5m 50 5m dimensions in mm 00 24

1- A simply supported beam is composed of three plates, which are fastened together using bolts that are spaced at 150mm intervals in the longitudinal direction of the beam. If the allowable shear on the bolts is 15 kN, what is the maximum allowable value of the applied load P? 24 24 Bolts spaced at 150 mm P 70 AB longitudinall - 1.5m 50 5m dimensions in mm 00 24

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Test#1 -zzen-zax AlpQLSdM75VMOVqbMa1WtS9n99RYc6PifeGUTpVBOluyMUUVYQgqqA/formResponse YouTube Replace the three forces which act on the bent bar by a force-couple system at *.the support point A 2100 lb 4' 1500 lb •A B. 30° C. 2' •E. 800 lb 3' oogle
4. A flanged bolt coupling consists of eight steel 20-mm voIs spaceu evenly around a bolt circle of300mm in diameter. Determine the torque capacity of the coupling if the allowable shearing stress in the bolts is 40MP.. Det the 4 ways to increare M3 HW 3 the torque capacity to 24 KN-m a) no. d bofts ) Ss d bolti c) Dia of bolts d) Dia of belt eircle) change vn ad Make sure that orly one aspect a
Given the following allowable stresses:• 50 MPa for shear in rivets• 100 MPa for bearing between a plate and a rivet• 80 MPa for tension in the platesDetermine the maximum load P that can be applied to the lap joint connected bythree – 16 mm diameter rivets. Note: Draw its FBD
CH2-Hetant pa-Aote Acrobet Pro titended Ee Vien Decumem Comments Forme Tacs adanced wedew Hep 2/86 If the resultant of the loads shown passes through point B, determine the equivalent force-couple system at O. 45 kN 54 kN 1.2 m 0.9 m 0.9 m M 18 kN ahid ham
10/- find the bearing stress between bolts and plate 80 kN 80 kN 8-bolt DIA. 10 MM 80 kN 80 kN 8-bolt DIA. 10 MM 125 MPa 12.5 MPа О 250 MPа no one O 8 mm 300mm 3. 4) -O--O O 5,
Q4\ Which of the following is a zero-force member? 3 8KN 4 G 4 エ子c D. 4 B AC BD IF ID
Question 3 Determine the capacity of plate as well as below connection based on Balts (4) in the below Following reactions :- 7 11 A325, $4 þ Bolts use! Use: AISC manual U Moment = 10 kip-67 2 kip (2) Shear (3) Axial 2 kip رب Ź Plate (A 36) 10 " x 10" x ≤ 11 8 HSS. их их nxuxt 4 H² 7
0: ll zain IQ docs.google.com/forms O no one 0/10 find the tensile stress in upper plate in section 1-1 5 1 80 kN 80 kN B-bolt DIA. 10 MM 80 kN 80 kN B-bolt DIA. 10 MM 30 MPa O 33 МРа 35 MPa 37 MPa no one + ... 300 mm
9. The gusset shown is riveted to the column flange by 7-20mm diameter rivet single shear. Determine the stress in the most heavily loaded bolt. If the design shear stress is 400MPA, determine the ultimate load that the connections can carry. Using the design shear stress how much more torque can the connections carry? 140 kN 200 mm 175 mm 7- 20 mm bolts 150 mm 150 mm 150 mm
O cd O efgh O ij O klmn O qrst V What is the line of action of which the section will yield in tension? All holes are the same diameter. O aflrsmgb O op t P n j h C d
CHomework 9 Problem 8.16 2 of6 Review Consder the truss shown in (Eoum.1). Assume the mombern are pin connected at their end points. Take A200 mm and E-200 GPa for each member Previous Anewers v Correct - Part B Detemine the vertcal daplacement ofir C mesd doww Ue Catglanos hem Express your anewer te three geare ngures and ineude theppripriate unta Enter pove vathe displecement dowwand and negative value if the displacement upward. Figure 24 KN 12AN 50.22 mm PreAne heAn X meorect, Try Again Ned Provide Feedac
11-12. A joint is fastened together using two circular bolts. A single plate carries 40 kN load. What is the actual shear stress if the allowable shear stress is 350 MPa and factor of safety is 2.5? A350 Pa CS with 6.5T5MP C. 140 Pa B. A D. 965 MPa Determine the diameter required using the actual shear stress. B. 8.53 mim C. 12.06 mm A. 13.49 mm D. 19.07 mm