1) A buffing wheel is connected to the shaft of a motor. When the motor is switched on, it takes the motor 6.1 seconds to rotate at 3602 cycles per minute. When the motor is switched off it takes the motor 69.8 seconds to stop. Assuming a uniform time rate of change of the angular velocity, when the working motor is switched off, how many cycles does it do to stop?

1) A buffing wheel is connected to the shaft of a motor. When the motor is switched on, it takes the motor 6.1 seconds to rotate at 3602 cycles per minute. When the motor is switched off it takes the motor 69.8 seconds to stop. Assuming a uniform time rate of change of the angular velocity, when the working motor is switched off, how many cycles does it do to stop?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In a motor, increasing the gap between electromagnets and a rotor: Select one: decreases motor torque. increases motor torque. increases motor speed. reverses the direction the rotor turns.
A short composite motor draw or pulls stream a current of 50 A at a voltage of 220 V it rotates at a speed of 1200 rpm Calculate the reverse electromotive force if the resistance of the product is 0.04 ohm the resistance of the series windings is 0.01 ohm and the resistance of the parallel windings is 125 ohm then Calculate the torque generated
A 2-pole, 50 Hz induction motor has an emf in the rotor the frequency of which is 2 Hz. Determine the rotor speed. Answer: 2880 rpm
In a motor-generator set, calculate the number of poles required in the motor to convert AC 25 Hz input, to AC 60 Hz output. Given that the number of poles of the generator is given as 24 poles. Select one: O a. Pm = 8 poles O b. Pm = 10 poles O c. Pm = 12 poles O d. Pm = 18 poles O e. None Clear my choice
To start a synchronous motor, the frequency of the applied electric power is reduced to decrease the speed of the stator magnetic field to a low enough value that the rotor can accelerate and lock in with it during one half cycle of the magnetic field rotation. Select one: O True O False
2. An armature has 268 coils and rotates at 900 rpm. Each brush covers 4 commutator segments. a) Find the time for one revolution . b) Estimate the interval during which a brush short circuits a coil. c) Why is your answer in part (b) approximate? 1000
A) Although the magnetic field for each phase of a 3-phase induction motor is merely switching back and forth between north and south poles, the resultant magnetic influence from all phases sets up a rotating magnetic field to cut the rotor conductors. a) true b) false B) In a two-pole stator winding of a 3-phase motor, how many revolutions does the rotating magnetic field make in one cycle of the electrical current? a) one b) 60 c) 3600 d) none of the above 3.
The field windings of a series motor has a resistance of 180 ohms at 30 degree Celsius. After running for 5 hours, the resistance increases to 140 ohms. If the temperature coefficient of the windings at 0 degree Celsius is 0.004. Find the new temperature of the windings. *
8. What happens to the magnitude of the magnetic field on the Rotor when an induction machine speed increases closer to synchronous speed? the rotor speeding up has on effect on the magnetic field on the rotor the rotor speeding up increases the magnetic field on the rotor the rotor speeding up decreases the magnetic field on the rotor
Draw occ at 800 rpm At 1000 rpm And 600 rpm and air gap Field Armature emf V Armature emf V Armature emf V current(A) At 800rpm At 1000rpm At 600rpm 8 10 6 0.3 28 35 21 0.5 46 57.5 34.5 1.0 94.5 118.125 70.875 1.5 143 178.75 107.25 2.0 175 218.75 131.25 2.5 195.5 244.375 146.625 3.0 211 263.75 158.25 3.5 224 263.75 168 4 234 280 175.875 4.5 243 293.125 182.625 5 252 314.375 188.625 6 266 331.875 199.125 7 277 347.5 207.375 8 286 368.125 214.5 9 295 368.125 220.875 10 302 226.5 226.5 The drawing must be handwritten without using a computer scale X-axis 1cm = 1 y-axis 1cm =20
A 240 V DC shunt motor takes 20 A and delivers 28 N.m at 1350 r.p.m, the efficiency is . O 73.63% O 80.325% O 82.467% O 89.964%
The current flows in the windings of the DC machine which causes the O Eddy current loss Friction loss O Ohmic loss O Hysteresis loss