1) A 0.5 meter diameter (D) concrete pile is driven into a sand deposit with y moist = 18.7 kN/cubic meter and o= 31 degrees. The water table is very deep. a. Assume Nq = 68.2. b. Assume K = 0.727 (Effective Earth Pressure Coefficient) c. Assume ô (friction of concrete surface to sand) = 24.8 (0.8 Tan 9) ESTIMATE PILE SHAFT ULTIMATE CAPACITY ASSUMING PILE IS 40 METERS LONG USING MEYERHOF'S METHOD. Assume critical depth is 15D. Hint: pile perimeter is 1.571 M

1) A 0.5 meter diameter (D) concrete pile is driven into a sand deposit with y moist = 18.7 kN/cubic meter and o= 31 degrees. The water table is very deep. a. Assume Nq = 68.2. b. Assume K = 0.727 (Effective Earth Pressure Coefficient) c. Assume ô (friction of concrete surface to sand) = 24.8 (0.8 Tan 9) ESTIMATE PILE SHAFT ULTIMATE CAPACITY ASSUMING PILE IS 40 METERS LONG USING MEYERHOF'S METHOD. Assume critical depth is 15D. Hint: pile perimeter is 1.571 M

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter12: Pile Foundations

Section: Chapter Questions

Problem 12.15P: Solve Problem 12.13 using Eqs. (12.59) and (12.60). 12.13 A concrete pile 16 in. × 16 in. in cross...

See similar textbooks

Similar questions

Determine the design capacity of the pile group shown below. The pile cap thickness is 1.5 meters, and groundwater table is located 2.8 meters below the ground surface. Piles are 350-mm in diameter and 12 meters in length. Use a critical depth equal to 18*dpile (starting from ground level), K = 3, ac (adhesion factor for clay) = 0.5, a, (wall friction angle for sand)= 25°, and FS = 3. Only consider single-pile action and neglect the capacity of the pile cap. Ground Level 1.5 m- Firm Clay c = 35 kPa Yary = 14.6 kN/m³ Yaut = 17.9 kN/m³ 3.5 m Medium Dense Sand 31° - 6.2 m Yary = 16.8 kN/m³ Yaat = 19.4 kN/m³ Layout of Pile Group Dense Sand 9 = 42° Yary = 18.2 kN/m³ Yu- 20.1 kN/m³ N - 200
A 50 cm square precast pile is driven by 9 m into a sandy soil. The standard penetration test results, prformed on this ground, are given in the table below: Depth below ground surface (m) SPT (Nss) 1.5 3.0 4.5 4 6 6.0 12 12 20 24 35 39 If the skin resistance is equal to {T, = 2 x (average Nss along the pile shaft)) kPa. Compute the factor of safety available, if 1100 kN of compressive load is applied on this pile. 7.5 9.0 10.5 12.0
A 16 in diameter, 55 ft long drilled displacement pile is to be constructed in the following soil profile. Depth (ft) Soil Description Unit Weight (lb/ft3) Undrained Shear Strength (lb/ft2) 0–10 Sandy silt 115 800 10–35 Silty clay 105 4000 35–50 Silty clay 112 1500 50–65 Clay 115 2000 The groundwater table is at a depth of 10 ft. Using a factor of safety of 3.0, determine the ASD allowable downward load capacity.
Refer to Figure 18.13. Given L1 = 1.5 m, L2 = 3 m; for the sand, =33, =16.5kN/m3, sat=19.0kN/m3; and, for the clay, c=50kN/m2, =0, sat=20kN/m3. Determine the depth of sheet pile required, allowing for a 50% increase from the theoretical estimate.
Refer to Figure 18.26b. Let L = 15.24 m, fill = 17.29 kN/m3, sat(clay) = 19.49 kN/m3, clay = 20, Hf = 3.05 m, and D = 0.406 m. The water table coincides with the top of the clay layer. Determine the total downward drag on the pile. Assume that = 0.6 clay. FIG. 18.26 Negative skin friction
Refer to the pile shown in Figure P9.1. Estimate the side resistance Qs by Using Eqs. (9.40) through (9.42). Use K = 1.5 and Coyle and Castello’s method [Eq. (9.44)]
Solve Problem 12.13 using Eqs. (12.59) and (12.60). 12.13 A concrete pile 16 in. × 16 in. in cross section is shown in Figure P12.13. Calculate the ultimate skin friction resistance by using the α method [use Eq. (12.61) and Table 12.11] λ method β method Use for all clays, which are normally consolidated.
A 30 m long concrete pile is 305 mm times 350 mm in cross section and is fully embedded in a sand deposit. Using Broms' method, calculate the allowable lateral load Q_g (take FS = 2) at the ground level. Assume the pile is flexible and restrained. Let the soil unit weight, gamma = 16 kN/m^3, the soil friction angle, Phi' = 30^degree; and the yield stress of the pile material, F_y = 21 MPa,
A frictional pile with a circular cross-section (diameter D) is pushed into the soil to a distance (L) and then it is subjected to an axial force (P) on its top end. Derive a formula to calculate the normal stress in any section x. P fN, D Cross section
A rectangular pile (0.88 x 0.68 m.) is driven in a clayey soil arrangement composed of two different layers. First layer has a height of 5 m., cohesion of 54 kPa, friction factor of 0.81. Second layer has a height of 8 m., cohesion of 72 kPa, and friction factor of 0.81. Compute the allowable load that the pile can carry if the factor of safety is 2.93. Use stored value. Asnwer in 5 decimal places.
Determine the primary consolidation settlement for the 20 m long pile group shown below. Soil properties by layer are given in the figure, and the clay layers are normally consolidated. Assume a 2:1 load spread starting at a depth of 2/3 of the embedment depth, L. The pile group is square and has dimensions 2.6 m by 2.6 m in plan view. The groundwater table is 1 m below the ground surface. = 4000 kN 1 m Sandy soil Y =18.5 kN/m³ Q'=330 V W.T. 7 m -Group.. piles Clay 1 Y =17.2 kN/m3 e=0.83 C= 0.23 L= 20 m Ax B = 2.6 m x 14 m 2.6 m Clay 2 Y =17.5 kN/m3 e,=0.78 C=0.22. 8 m Clay 3 Y =18.0 kN/m? eo=0.76 C=0.20 12 m Rock
Q1/ For the footing shown in Figure (1), estimate the pile group capacity. 0.6m dia bored pile Clay c=80 kN/m² y-17kN/m² S=1.5 m T L=12 m