1 .. 3. For the three-hinge arch below, let Fı = 10 lbs, F2 =20 lbs, H1 = 5 feet and L1 = 5 feet. F1 and F2 act at L1/2 from A and L2/2 from C, respectively. Determine the reactions at the supports (A & C) and the pin forces at B and write your final results in the table below for the following conditions:

1 .. 3. For the three-hinge arch below, let Fı = 10 lbs, F2 =20 lbs, H1 = 5 feet and L1 = 5 feet. F1 and F2 act at L1/2 from A and L2/2 from C, respectively. Determine the reactions at the supports (A & C) and the pin forces at B and write your final results in the table below for the following conditions:

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

= The strut AB made from two bars (thickness of each bar = 0.50 in) is connected to a rectangular beam CD (b 0.80 in x h = 7.5 in) at joint B. The beam carries a concentrated load of 2750 lb at the end joint D. (a) determine the minimum diameter of the bolt at B if the shearing stress in the bolt is not to exceed 14000 psi. (b) determine the minimum diameter of the bolt at B if the allowable bearing stress in the bar plate is 20000 psi. Detail of joint B 3 ft (O с A 5 ft O B 6 ft D 2750 lb 3.75 in 3.75 in 0 in 0.80 Strut AB Beam CD (b Xh) Bolt (dmin) -0.50 in
The steel truss (E =200 GPa) shown in figure below has a cross-sectional area of 1920 mm². Determine: a. The largest allowable load F if the change in length of member BD is not to exceed 1.6 mm and a factor of safety of 2.5. b. The displacement of support D due to the load calculated in part a. 5m 6m A C F
If the allowable bearing stress for the material under the supports at A and B is Ob = 780 psi, determine the maximum load Pmax that can be applied to the beam. The bearing plates each have square cross sections of 5 in. by 5 in. The reactions at the supports are vertical. Assume w = 600 lb/ft, a = 12 ft, and b = 6 ft. Answer: Pmax= i W a B b lb P
Determine the force in each member of the truss shown. Use a=1m, b=3.1m and P= 10 kN. Box your final answers. 4@4m=16m P 18 kN B a 5m 6m G 5m 27 kN 36 KN
How do i solve the attached trusses/civil engineering problem?
At the beginning of your solution, write down the values of P1, P2, P3 and L and solve the followings using the section method: 4- The internal member force FBC; 5- The internal member force FBE.
Given the Truss as shown below with load P = X N and P2 = 3X N. Using Method of Joints, determine the following if the maximum force at member CG is 62.50 N (Compression). a.) The Load P,. b.) The Load P,. c.) The Force at Member GF. В C D 2 m A E G F -1.5 m -1.5 m 1.5 m -1.5 m P1 P2 Note EXPRESS YOUR ANSWER UPTO 3 DECIMAL PLACES.
Calculate the forces in members BE and BD of the loaded truss. The forces are positive if in tension, negative if in compression. Assume F = 7.5 kN, a = 2.5m, b = 3 m, c = 2 m, and d = 2 m. A F Answers: BE= BD = a i i B b E a b O KN KN
A simple pin-connected truss is loaded and supported as shown. The truss is constructed from three aluminum members, each having a cross-sectional area of A = 1160 mm2. Assume a = 2.3 m, b = 6.8 m, and c = 2.8 m. If P = 50 kN and Q = 75 kN, determine the normal stress in each member. L. Answers: JAB OBC i i JAC= i P b MPa (C) MPa (T) MPa (T)
truss. need asap
Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Consider the given structure with P= 952 lb. Во 12 ft The force in member AB is The force in mémber BC is P Using the method of joints, determine the force in each member of the truss shown. State whether each member is in tension (7) or compression (C). The force in member AC is 3.75 ft 9 ft lb (Click to select) ✓ lb (Click to select) V lb (Click to select) ✓
ENGINEERING MECHANICS (UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS AND FBD LEGIBLY. NO LONG EXPLANATION NEEDED. BPX THE FINAL ANSWER. ANSWER IN 2 DECIMAL PLACES.) Given the Cantiliver Truss. Solve for the following: a. Solve for the reactions at A and B. b. Solve the force in members EF, DE, DF by using any methods.