0. A polluted river sample is analyzed using standard BOD procedures. Data obtained are listed below. Determine the BOD,, BOD, and k values that best fit the data. TIME, d 0 1 2 3 4 5 6 7 DISSOLVED OXYGEN, B/m² Dilution, mL/300 mL 1 5 8.77 7.66 8.90 8.83 8.76 8.69 8.62 8.55 8.48 8.41 8.87 8.49 8.41 8.23 8.06 7.91 7.77 7.64 30 8.11 2,70 7.25 0 6.39 5.83 5.35 4.95 4.60

0. A polluted river sample is analyzed using standard BOD procedures. Data obtained are listed below. Determine the BOD,, BOD, and k values that best fit the data. TIME, d 0 1 2 3 4 5 6 7 DISSOLVED OXYGEN, B/m² Dilution, mL/300 mL 1 5 8.77 7.66 8.90 8.83 8.76 8.69 8.62 8.55 8.48 8.41 8.87 8.49 8.41 8.23 8.06 7.91 7.77 7.64 30 8.11 2,70 7.25 0 6.39 5.83 5.35 4.95 4.60

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A falling head permeability test was run on a soil sample 12.3 cm. in diameter and 11.4 cm. long. The head at the start of the test was 93 cm. and falls to 73 cm after 38.2 mins. The diameter of the stand pipe was 1.54 cm. Determine the flow rate (in cm^3/min) through the soil. Use head loss method. Round off to four decimal places.
A falling head permeability test was run on a soil sample 9.60 cm in diameter and 10 cm long. The head at the start was 70 cm. The coefficient of permeability of the soil was found to be 5 x 10-6 cm/s. The diameter of the standpipe was 1 cm. What is the rate of flow at the start of the test? Select the correct response: 6.08 cm/hr 11.73 cm/hr 15.83 cm3/hr 9.12 cm/hr
A primary clarifier is to be designed to treat a municipal wastewater. The influent to the clarifier has a flow rate of 7570 m³/d and a total suspended solids concentration of 320 mg/L. A laboratory settling test was performed with the following results: Suspended Solids Concentration (mg/L) at Given Depths Sampling Depth (m) Time (min) 0.61 1.22 246 2.44 272 243 1.83 3.05 10 230 262 282 20 157 195 230 253 30 115 160 211 221 230 45 90 134 163 179 195 60 48 102 131 154 170 90 29 58 86 115 141 (a) Determine the design overflow rate and detention time assuming 65% of the suspended solids are to be removed. Use typical scaling/safety factors as appropriate. (b) Determine the required diameter (to the nearest 0.1 m) and the required depth (to the nearest 0.01 m) for the clarifier.
Calculate the followingi. Liquid limitii. Plastic limitiii. Plasticity index
Solve with complete solutions
A water sample is analyzed for BOD on a daily basis for 7 days using the dilution method. Results of analysis show k-0.23d¹ and BODu = 15g/m³. Twenty day samples have also been analyzed and the BOD value is consistently 23 g/m³. What might cause the difference between estimated and measured BOD values?
Please answer all 1. List the three corrections which should be applied to the hydrometer readings. 2. Why is it important to remove the hydrometer from the measuring cylinder between readings? 3. A hydrometer test has the following results; Gs = 2.70, temperature = 240C, and L = 92 mm at 60 minutes after the start of sedimentation. Calculate the diameter of the smallest-size particles that have settled beyond the zone of measurement at that time (use the table in the lab manual to find, A=0.0128). D(mm) = A sqrt( L(cm) / t(min) )
A falling head permeability test was run on a soil sample 9.60 cm in diameter and 10 cm long. The head at the start was 90 cm. The coefficient of permeability of the soil was found to be 5 x 10-6 cm/s. The diameter of the standpipe was 1 cm. What is the rate of flow after 30 minutes? Select the correct response: 10.79 cm/hr 11.04 cm/hr 9.10 cm3/hr 6.46 cm3/hr
please show all your solutions dont shortcut it please answer it by week with complete solutions then after put it in a table form
Determine the three Atterberg Limits from the given data.
Question 1
A liquid limit test conducted on a soil sample in the cup device gave the following results: N 10 19 23 27 40 w (%) 60.0 45.3 39.8 36.5 25.2 The plastic limit test and natural water content. Natural Water Content Test Test No. Weight of Container + Lid (g) Weight of Container + Lid + Wet Soil (g) Weight of Container + Lid + Dry Soil (g) Plastic Limit 2 2 13.07 13.18 7.84 7.5 22.12 21.84 17.53 16.97 20.59 20.35 15.45 14.93 The shrinkage limit test. Weight of Dish with petroleum jelly (g) Weight of Dish with petroleum jelly + Wet Soil (g) Weight of Dish with petroleum jelly + Dry Soil (g) Volume of Shrinkage Dish (cm³) Volume of Oven-Dried Soil Pat (cm³) 11.3 38.51 32.81 15.26 12.83 27. Determine the liquid limit. b. 39% 28. Determine the plastic limit. а. 38% С. 37% d. 40% a. 20.56% b. 21.20% C. 21.85% d. 20.20% 29. Determine the shrinkage limit. b. 22.40% а. 15.20% C. 18.59% d. 16.45%