### Explanation of Logic Circuits#### Diagram DescriptionThe image contains two diagrams of logic circuits:1. **First Circuit:** - Two inputs, each labeled "1," connect to an AND gate. - The output of the AND gate connects to a NOT gate. - The final output is labeled "0."2. **Second Circuit:** - Three inputs, each labeled "1," connect to an AND gate. - The output of the AND gate connects to a NOT gate. - The final output is labeled "0."#### Questions(a) Is the logical circuit built in Step 3 (b) working without errors? Yes/No (0,1 input error)(b) What is the difference between a built-in AND/OR circuit and a built-in NOT circuit for use?

Answered: Image /qna-images/answer/b2df3fb1-4a24-430c-bab5-39d932828bda.jpg

Answered: (0)) (a) Is the logical circuits built…

(0)) (a) Is the logical circuits built in Step3 (b) working without errors? Yes/No (0,1 input error) (b) What is the difference between a built-in AND/OR circuit and a built-in NOT circuit for use?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Reduce the Boolean function specified in the truth table below to its minimum SOP form using K-map, where A, B, C are the inputs while X are the outputs. Based on the reduced Boolean function, design the logic circuit using any logic gates. A 0 0 0 0 1 1 1 1 B 0 0 1 1 0 1 с 0 1 0 1 0 1 0 1 X 1 1 0 1 1 1 0 1
a) In Assembly programming what is the functionality of the following instructions DECFSZ ВTESC MOVLW MOVWF goto b) A piece of code is required for a time critical activity. Should this be written in assembly language or C? Explain your answer. 5 Explain the difference between the (For) and (While) loops. Highlight the main components of the (For) loop that are required for its execution. Consider the following C program designed to run on a PIC 18F4455. int main(void) 2 { 1 double voltage; double current; double milliwatts; double energyUsed; double cummulativeEnergy = 0; while (1) { voltage=analogRead (VOLTAGE_PIN)*voltageScaleFactor; current=analogRead (CURRENT_PIN)*currentScaleFactor; milliwatts=voltage*current; energyUsed=milliWatts*0.5; cummulativeEnergy=cummulativeEnergy+energyUsed; 10 11 12 13 14 15 _delay_ms (500); 16 } 17 a) What is the role of the symbols "{" and "}" b) The code here is indented. Explain the importance of indentation N m 4 n Or 00 o A m
What is the purpose of the break statement? Force the termination of a program. When a break statement is encountered in a loop, the loop terminates immediately and the execution resumes the next statement following the loop. To produce the systematic code, and the break statement does not affecting the program. To make the code easy to understand.
Using appropriate diagrams, explain how a combination of transistors and resistors would be used to construct an OR logic gate to control the flow of electrons inside an integrated circuit. please show mw how to do the digram
A d. B Figure 1 3. Referring to the logic circuit in Figure 1, determine: a. The simplified Boolean expression. b. The output waveform. C H c. Due to fabrication errors, lines d and f were shorted to the supply voltage. What happens to the output of the circuit? d. Your hardware resources are limited to 2-input NOR gate only. Draw the gate schematic of the simplified Boolean expression in 3(a).
LOGIC GATE ( NEED ONLY HANDWRITTEN SOLUTION PLEASE OTHERWISE DOWNVOTE).
.Provide a detailed report on the combinational logic circuits below. 1. Magnitude Comparators a. What are magnitude comparators? b. How does it work? c. Applications of magnitude comparators.
Please prepare task according to image.Thank you!
(c) Identify and draw the simplified logic circuit for Figure Q5(c) by using only a single (1) logic gate that can be applied to replace the whole circuit. Figure Q5(c) X
6. Modify your experiment circuit so that it appears as shown in Figure 3.2. One logic input will come from SW1. The other logic input will be a 1Hz clock (CLK) signal from the FUNCTION GENERATOR. You will monitor the gate output with LED DISPLAY L1 and the clock output on LED DISPLAY L2. + 5V 1K SW1 CLK LED INDICATOR (1Hz) Figure 3.2 7. Set SW1 to Binary 0 (down). Note the output on L1. Then set SW1 to binary 1(up). Again note the output on L1. Explain your result, SW1 = 0; Output C = SW1 = 1; Output C = What logic function does this gate performing? 12 V 10 k Ohm IN4001 SW1 OUTPUT INPUTS IN4001 sw2 Figure 3.3 8. Construct the logic gate shown in Figure 3.3. (note for the -12V supply and the 10K resistor). Again, DATA SWITCH SW1 and SW2 will supply the logic input D and E, and you will measure the output voltage at F with a voltmeter.
I will make the implement part myself. Hello, Please do what is requested carefully. Logic circuits answers that I usually get from Bartleby are wrong. Please ensure.I will post the question 3 times.Can you answer Question A?
The diagram shows a transistor used to interface a logic gate to a lamp for it to be fully lit. Resistance of lamp=80 ohms 9Vo Signal from logic gate Ovo R Logic gate Output 0.2V 3.3V IB V₁ Lamp a) The logic gate outputs 0.3 for logic 0,and 3.3V for logic 1. Complete the table below to show the effect of these signals on the transistor and lamp by: i) Adding the correct voltages to the V1 column ii)writing either 'Off' or On to show the state of the lamp V1(V) same as VB When filly lit the, the lamp passes a current of 100mA. The transistor has a current gain, beta ẞ of 60 b)Calculate the base current, IB. c)Using KVL find the voltage drop across R. Sate of lamp