-.11 Determine the resultant of the coplanar concurrent force sys- tem shown. Determine the magnitude, sense, and angle of inclination with the X axis. Use the method of components. Y 400 lb X X 70° 45° 200 lb 300 lb

-.11 Determine the resultant of the coplanar concurrent force sys- tem shown. Determine the magnitude, sense, and angle of inclination with the X axis. Use the method of components. Y 400 lb X X 70° 45° 200 lb 300 lb

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter1: Introduction To Statics

Section: Chapter Questions

Problem 1.72P: Determine the value of the scalar a if the following three vectors are to lie in the same plane:...

See similar textbooks

Related questions

Q: calculate the leakage mass flow rate per unit area from the first ring pack plenum to the cylinder…

A: Given Temperature, T = 450 K Coefficient of discharge, C = 0.75…

Q: 2.A steam throttling valve with inlet conditions of 2MPA and 400C is connected to the inlet of the…

Q: For the air duct shown below, if the total pressure of air is 250 kPa and the static pressure is 50…

Q: Study the double slider crank mechanism in figure A: (a) Using Aronhold Kennedy Theory formula,…

Q: .Determine the moment of the 1800-N force about (a) point C and (b) point B of the engine hoist…

A: Calculate Moment of 1800N about C and B

Q: Prove that there is an increase in efficiency between a Simple Rankine Cycle and a Reheat Rankine…

A: Given data Reheat Rankine cycle with the following conditions: Steam entry at High pressure turbine…

Q: What are the Rotational / Translation Motion equations ?

Q: convert 3.5 in to nm 9:08 PM

A: Given 3.5 in

Q: 4. At a proposed hydroelectric power plant site, the tailwater elevation is 470m. The estimated…

Q: 120 mm 3) Determine the location y for the beam having the tapered cross-sectional area shown…

A: ȳ = 135 mm

Q: Draw the three projections of the body in Figure 1- using AutoCAD 1-Do not write the dimensions on…

A: Find Draw the three projections of the body.

Q: What are the importance of Ceramics in Engineering? Give some examples

A: Ceramics : Ceramics are the materials which is inorganic and nonmetallic materials that are…

Q: Micro-hardness profiles were obtained for the tool steel, the weld zone and stainless steel. Figure…

A: A statement is given that " the dents on the stainless steel is larger than those on the tool…

Q: Calculate the maximum moment in a 40-foot simply supported beam due to the following axle loads: 24k…

Q: 2 -Determine the magnitude (P) of the horizontal force required to initiate W=30 N motion of the…

Q: 1. the temperature in evaporator coil is -6 oC and that in the condenser coil is 22 oC. assuming…

Q: Find the surface area of the plane ( 15x- 5z+20Y3D35) if it is in the first octant

A: Given: The equation of the surface: →15x-5z+20y=35 if x=0,y=0 then→15×0-5z+20×0=35 →z=35-5=-7if…

Q: 11. a heat pump using R-717 as a refrigerant operates between saturated temperature of 6 oC and 38…

A: Refrigerant=R717Evaporation temperature, Te=6oCCondenser temperature, Tc=38oCUnder cooling in the…

Q: Figure P3-41 3-41 For the insulated corner section shown in Figure P3-41, derive an expression for…

Q: The answers are the same. Why is it wrong?

Q: 3- Two cars moving towards cach other, separated by 150 km, If the first car has a speed of 60 m's…

A: The necessary time for them to meet together: t = 25 minutes

Q: Derive the mass moment of inertia about the central x-axis of the hemisphere shown below. Assume…

Q: Q2/ Which part of speech the word "patently" ?belongs to „Adverb .a .Noun .b .Adjective .c .None one…

A: The patent is a verb or noun and it can be an adjective.

Q: 1- The initial velocity of the block in position A is 30 m/s. Knowing that the coefficient of…

A: Dear student, I have derived a general expression for time. You can put any value of theta and get…

Q: A container is floating in water. The container has a rectangular shape of 1.52 X 0.66 X 0.50 m…

Q: Draw isometric

A: Find Isometric View

Q: the strain percentage in the direction of the normal force is

Q: A rigid tank initially contains 5kg of saturated vapor steam at 150°C. Heat transfer is done until…

A: Given: Mass of the saturated vapor→m=5 Kg Initial temperature of the saturated vapor→Ti=150°C…

Q: Please help! Thank you! - Evaluate the definite integrals using (a) integration, (b) trapezoidal…

Q: d) A 0.3 cm thick aluminum plate (40 W/m. K) has rectangular fins on one side, 0.16 x 0.16 cm,…

Q: Calculate the reactions at A and B for the beam shown. Neglect the weight of the beam. 6 kips 7 kips…

A: To calculate the reactions at supports.

Q: Find the center of gravity of the following flat, thin, homogeneous, composite objects in the…

Q: efficiency for ammonia compressor designed with 4 % clearance and operating between condenser and…

A: Solution is attached below

Q: 13. A pump forces 1.2 m3/min of water horizontally from an open well to a closed tank where the…

A: (13) Given that, Volume flow rate, V˙=1.2 m3/min,Pressure of water, P1=0.9 MPa,Atmospheric pressure,…

Q: A torque T = 1500 N – m is applied to the hollow shaft shown that has a uniform 10 mm wall…

A: find shear stress at point a and b and angle of twist.

Q: QL Match list (1) with list (T) and select the correct answer? la Type of chip 1 Continuous chip. 2…

A: Different types of metal forming processes used in engineering applications are: Forging Casting…

Q: CI Answer of the following: 1. According to the SAE viscosity classification, the oil (SAE 40) is…

A: Ans: 1 ... It's false. The oil (SAE40) is higher viscosity as compared to oil SAE20 at same…

Q: Evaluate the given integral. dx 1+e2x

Q: A hockey puck is traveling to the left with a velocity of v, = 12 m/s when it is struck by a hockey…

Q: 1. Thin steel plates are subjected to a steady stream of air flowing along their surface at 2 m/s.…

Q: The post is constructed from concrete and six A-36 steel reinforcing rods. If it is subjected to an…

Q: A long concrete footing rests on an earth founda- tion for which the value of the foundation modulus…

A: We know that a lengthy concrete footing is supported by a 5.6 MN/m2 foundation modulus. The footing…

Q: Propane is burned completely with 25% excess air. Compute the number of moles of nitrogen in the…

Q: Question 1 of 18 <. Perform the conversions. 1.167 atm= Torr 931.7 mmHg = atm Pa atm 1108.9 mmHg =…

Q: A liquid having sp. gr. of 2.0 is flowing in a 50 mm diameter pipe. The total head at a given point…

Q: Choose correct answer Load carrying capacity of journal bearing is independent on a)Bearing…

A: Explanation: Load carrying capacity of journal bearing depends on 1) Rotational speed 2) Applied…

Q: What are the differences between austenite phase and martensite phase in shape memory alloy? What…

A: Austenite phase exists at higher temperature whereas martensite phase exists at lower temperature.…

Q: .15 An inclined cable is used to pull on a log as shown. Determine the magnitude of the force…

A: Assuming the surface on which the log is kept as frictionless and the log itself being massless.

Q: A steam throttling valve with inlet conditions of 2MPa and 400C is connected to the inlet of the…

Q: 1.40 Convert the following quantities to the designated SI units: (a) 627 in? to mm² and m2 (b) 14…

A: As per our guidelines, we are supposed to answer only first three subparts in case of multiple…

Question

Please show all work and how you did it with proper units and Full body diagram if needed. Thanks

3.11 Determine the resultant of the coplanar concurrent force sys-
tem shown. Determine the magnitude, sense, and angle of
inclination with the X axis. Use the method of components.
Y
400 lb
X -
70°
45°
200 lb
300 lb
Y

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Find the y-component a force, 100N, acting 45 degrees to the right of the negative y-axis.
1. Aforce of 200 N is directed up to the left of an angle 30 degrees with the x-axis. Determine the component of the givenx and y. 2 Determine the force F in concurrent force system to produce a resultant of 155 kN, downward to the right, 35 degrees with respect to x axis. 30 kN 10 KN 15 deprees 65 degrees 80 kN Please express your answer in 2 decimal places and box your final answer. Kindly write clearly too. Thank you ©
3. Find the resultant and the location of the following parallel force system. A150 lb |lo lb solb 7516. A TITINIA ft. íz ft.
3. Solve for the Resultant of the force system shown and its direction with respect to the positive x-axis. 300 N 40° 30° 400 N 200 N
Q2. Find the resultant ( R ) of the force system shown. Show its position with resnect to point (O). Also show where it cuts both x – and y- axes. 200N SooN 600 N-m 2m 150 N 5m
The component of the following * force alongu axis is
Please solve with complete solutions and complete figures and enclose the final answer thank you. Given through the indicated points: A=280kN (12, 6, -4); B=520kN (-3, -4, 12); and C=270kN (6,-3,-6). Determine the resultant of the system of concurrent forces and the direction cosine of each of the axes having the following magnitudes, and passing through the origin.
Find the magnitude and direction of the resultant of a 60-pound force acting at an angle of 40 degrees clockwise from the positive y-axis.
What is the corresponding magnitude of the resultant?
Q4b. Force vectors F1 and F2 act on body Pwith the resultant force vector R. The resultant force R= 575 N and the angle between Rand the x-axis is of 320. If F1 = 275 N and the angle between F1 and the x-axis is 560, determine the angle between F2 and the x-axis. *Assume coplanar vector forces and give your answer in degrees to two decimal places. Body, P Answer: y F1 R F2
ind the resultant of the following forces by polygon method: F1= 12N, 270 degrees: F2= 24N, 30 degree north of west; F3=15 N, 75 degree south of west; and F4=32 N, 50 degree south of east
= Determine the resultant of the force system in next fig. Then locate it with respect to point (A). 1000 N.M. 150 N 100 N