. How many color bands are used on resistors that have a tolerance of ±20 percent?   Select one: A. FIVE B. FOUR C. SIX D. THREE

Q: Draw the block diagram of digital Multimeter and explain the measurement of D.C voltage

A: Digital multi meter is a measuring device which is used to measure AC and DC voltages, AC and DC…

Q: Determine the current flowing through the LED. (assuming its forward voltage is 2.1 volts) * A D1 D2…

A:

Q: what are two main advantages of using cermet in fixed resistors?

A: The Cermet film resistors are the film resistors comprised of an uncommon material called Cermet.…

Q: Identify the statement from the following why silver allows electric current. O a. It has low…

A: In this answer let us try to understand the reasons which makes the silver to.allow the electric…

Q: An IC resistor has a nominal value of 10 kΩ and a tolerance of ±30 percent. A particular process run…

A: Given RNOM = 10 KΩ, Resistance Average value equal to 20% higher than nominal value Calculating Ravg

Q: how to find the resistor band color using only the nominal value and 4th band resistance.. Ex.…

A: Given:Nominal Value of a resistance is 3.3 kilo Ohms, 4th band gold, 5% resistance.we need to…

Q: What is the circuit in the given 1 point diagram called? R VIN D1 D2. Vo VRI I VRZ

A: In this circuit there is no capacitor is present .

Q: What is the purpose of shunt resistors in an ammeter? A. To shorten the range of the ammeter. B.…

A:

Q: A voltmeter that reads 0.100 volts has a 200-division scale that can read up to half a division.…

A: Given,Range of the voltmeter is 0-100 Volts.Divison on the scale is 200.The voltmeter  can read up…

Q: Example: If PMMC meter have internal resistance of 102 and full scale range of 1mA. Assume we wish…

A:

Q: Which of the following increases its resistance if the temperature increases? I. Conductors II.…

A: I. Conductors - A conductor readily carries electricity because it provides minimal  resistance to…

Q: (e) Given the Wheatstone bridge of figure I with the galvanometer reading indicating the variable…

A:

Q: D1 D2 R1 5V 1K Determine the voltage across the resistor R1. (assume LED forward voltage is 2.1…

A:

Q: explain briefly and consicely the importance of tolerance in resistors

A: Tolerance of resistor is the nothing but how much is the resistance value measured of its actual…

Q: 5. Determine the total resistance if each Ris 30. RT M

A:

Q: Determine the resistance and tolerance of each of the 4-band resistors shown below.

A: We need to find out the resistance value for the above two resistors.

Q: i) A linear potentiometer of 300 2 is used as sensor to sense linear displacement. For a…

A: consider the given question;

Q: The application of rectifiers are (you can choose multiple answers) DC motor speed control UPS…

A: Dc motor speed control has not contain rectifier UPS CONTAIN RECTIFIER REGULAR DC  POWER SUPPLY…

Q: 7. A certain cooper wire has a resistance of 25 ohms at 10°C. Take the temperature coefficient at…

A: This question belongs to electrical circuit theory.  It is based on the concept of relation between…

Q: finding the tolerance value of green blue green and gold

A: green→5blue→6green→100kgold→5%( tolerance band)

Q: What is the circuit in the given diagram called? * R D1 D2 VIN Vo VrI T VR2 O Half Wave Rectifier…

A: This circuit have resistance , 2 diode and 2 battery.  Input voltage is Sinusodial waveform. The…

Q: Resistors are examples of .........................electronics device. Select one: O a. O b. O C. O…

A: Resistor : -A resistor is an element of an electronic circuit that restricts or controls the…

Q: What is the circuit in the given diagram called? * R VIN D1 D2. Vo VR2 I Vaz VRI O Clamper Full Wave…

A: we will analyze circuit  for various values of input voltage and based on the output we will decide…

Q: Identify the statement from the following when the inductance can have high value. O a. All the…

A: Inductance  L= uN^2A/L  U is permeability  L is the length of the coil A is the area of the coil  N…

Q: 2. List three differences between a P-type and an diagram) N-type semiconductor. (you can use

A: The detailed answer is solved below according to the given parameters and instructions in the…

Q: certain type of printer can print 50 pages in 3 minutes. How many pages can 4 printers of the same…

A: We need to find out total number of pages that given printer can print.

Q: Which of the following is NOT a common use of resistors in electronic circuits? A. Olimit current…

A: In this we will write use of resistors in electronic circuit...

Q: Q. The input for any circuit at lab experiments are O B. the switches OD. None of the above O C.…

A: While performing the experiments in Laboratory, the inputs is given at one terminal and switches and…

Q: Of the Type A electrical resistors produced by a factory, 85.0% have resistance greater than 41…

A: The answer is  14.1%

Q: What is the circuit in the given diagram * ?called R DI D2 Vo VIN VRI VR2 Clamper Not all above…

A: When  → VIN ≤VR1      D1 - OFFVIN > VR1      D1 - ONVIN<VR2     D2 - ONVIN >VR2    D2 -…

Q: What is the circuit in the given * ?diagram called R VIN DI D2 Vo VRI Clamper Clipper O Not all…

A: As diode are with a battery in series so it is clipping the input at output by VR1 and VR2

Q: How does a voltmeter differ from a potentiometer? What type of meter is the Corning- 10 pH meter?

A: A voltmeter and a potentiometer are two different types of measuring instruments used in electrical…

Q: c) Two of you have been given two instruments with the units in ohms, your colleague measures the…

A:

Q: Determine the voltage across the resistor R1. (assume LED forward voltage is 2.1 volts and Diode…

A: In this question,   We need to determine the voltage across the resistor R1.   If LED forward…

Q: Question V  What is the resistor range if the LED has a forward voltage of 1.7V. Supply voltage is…

A:

Q: The resistivity of a semiconductor decreases with increasing temperature since Lütfen birini seçin:…

A: We need tell about the effect of temperature on  resistivity of semiconductor.

Q: If a difference of 2.15 volts is applied to an unknown resistance and the measured current is in…

A: The potential difference between two points is given by the difference of voltage at the two points.

Q: One of the following electrical tools is used to create circuits without soldering: Circuit Board O…

A: Given :   1. Here in this question they are interested to know the electrical tool which is used for…

Types of Diode

Diodes are used to protect circuits by using electrical power restrictions and converting AC to DC. Semiconductors such as silicon and germanium are used to make diodes. Or they transmit power in one way, and the way they transmit it is different. There are different types of diodes, and each type has its own system.