. Determine the magnitude of the force on pin at A for the jip crane as shown in the figure. The beam AB is a standard 0.5 m l- beam with a mass of 95 kg per meter of length. 0.25 m 25 0.5 m 15 m 0.12 m 10 kN 5 m

Q: PROBLEM 1 Draw the shear force and bending moment diagrams of the cantilever beam shown using METHOD…

A:

Q: You have been tasked with designing a beam to support a lifting crane. The applied load is offset…

A: Given: A simply supported member subjected to two point loads of 4kN and 1.5 kN apart from each…

Q: Each rmember of the frame shown in figure below weighs 50 kN/m. Compute the horizontal and vertical…

A:

Q: will G. The 50N block C rests on uniform bar AB having a weight of 20N. The cable connecting C to B…

A:

Q: M= 100 KN.m 300 KN/m 1.0 m 1.0 m 1.0 m 3.0 m R1 R2

A:

Q: A mild steel bar, circular in cross-section, tapers from 40 mm diameter to 20 mm diameter over its…

A: Given data- Mild Steel bars-dia D varies from 40 mm to 20 mmLength L=800 mmAxial load P=20 KNYound…

Q: Find the midspan deflection o for the beam as shown, carrying two triangularly distributed loads.…

A:

Q: Replace the beam shown in the figure by a wide flange. The maximum flexural stress of steel is 120…

A: Wide flange

Q: 9- What is support reaction force (kN) at support A? 20 kN 3m 1,5 m Bos birak

A: Finding out support reactions at A.

Q: D 40 kN pin-jointed frame C F E HE MA EI EI 2EI 120 kN VE 4.0 m 4.0 m 4.0 m 4.0 m 3.0 m

A:

Q: Q3- Determine the design moment capacity of the T beam shown in Figure below iff=420 and fe= 35 MPa.

A:

Q: A beam is loaded with a distributed load as shown. Given that wo = 415 lb/ft, the equivalent…

A: Answer  We can determine the location of equivalent concentrated load  to the right of A by using…

Q: Consider the loaded beam in the figure: Choose the correct shear force diagram? 5 kN 5 kN/m A B to 2…

A:

Q: For the structure shown in Figure P-916 is hinged to fixed supports at A and E. Compute the maximum…

A:

Q: 2. An 8-m long steel column is pinned at the top and fixed at the bottom. The column is provided…

A: - Critical Effective slenderness ratio about x axis ; λ = KLxrx K = 0.7 Since one end is fixed and…

Q: Q2/ A simply supported beam supports the applied loads and moments as shown, calculate the support…

A:

Q: Replace the loading on the beam shown with an equivalent resultant force and specify its location…

A: Equivalent resultant force Ry = 12×2.5×5 + 1.2×2 + 12×2.5-1.2×2 + 1.2×3 +6…

Q: Determine the normal force at section passing through point E. Express your answer to three…

A:

Q: What is the horizontal support reaction RAX at support A for the ?frame shown below 35 kN/m B 15 m A…

A:

Q: X is L/2 For the frame shown above is constructed out of circular tubes for both the beam and…

A:

Q: 58 kN/m For the beam and loading B A C shown in figure, answer the Hinge questions below -5.5 m 254…

A: Reactions take right moment at B=0-VC×a+58×a22=0VC=29aand    VA=58×5.5-29a=319-29a

Q: The load system as shown in figure, moves from left to right on a girder of span 10 meters. The…

A: For given arrangement,To find the absolute maximum bending moment

Q: A simply supported beam with overhang is shown. 1,200 lb 450 lb/ft B 14 ft 6 17

A:

Q: Calculate the support reaction at roller support B

A: Find support reaction at B

Q: The beam below supports 2 distributed loads, and a point load, as shown. The beam is supported by a…

A:

Q: The T-beams for the floor system shown in the following figure support Live load floor of 30 kN/m…

A: The part of the slab which acts substantively with the beam to oppose loads is called the flange of…

Q: Consider the beam shown in (Eigure 1). Suppose that P = 3 kip, w = 1.1 kip/ft. Point E is just to…

A:

Q: plastic bea section is up by giuing togetner three strips, ) mm × 60 mm in cross section (see…

A:

Q: Derive the fixed end moments of the following beams shown.

A: Question is based on the fixed beam with point load at center of the span . In the question we have…

Q: 50 a load of 4 kN/m along its span. The beam cross section is made up of several pieces of wood as…

A:

Q: Determine the ultimate moment capacity of the beam shown using this data: b = 900 mm = 100 mm d =…

A: The given data is shown below: bf=900 mmt=100 mmd=450 mmAs=9852 mm2bw=300 mmfy=276 MPaf'c=28 MPa