.) A 300 MW pulverized coal-fired power plant of 42% efficiency uses coal with an ash content of 19% and aneating value of 24,000 kJ/kg. Assume 28% of the ash content goes up the stack as particulate matter in the flue gas.The PM emission is controlled by an ESP which has the following efficiencies and weight distribution in the given sizeranges. Find the fly ash emitted in g/s.sizeefficiency (%)wt% in flue gas0-57075-1092.51910-20962120-409924>4010029

Capacity of plant = 300 MW Efficiency of power plant = 42% Ash contains in flue gases = 28% Heating…

.) A 300 MW pulverized coal-fired power plant of 42% efficiency uses coal with an ash content of 19% and a ating value of 24,000 kJ/kg. Assume 28% of the ash content goes up the stack as particulate matter in the flue gas e PM emission is controlled by an ESP which has the following efficiencies and weight distribution in the given siz ges. Find the fly ash emitted in g/s. size efficiency (%) wt% in flue gas 0-5 70 7 5-10 92.5 19 10-20 96 21 20-40 99 24 >40 100 29

.) A 300 MW pulverized coal-fired power plant of 42% efficiency uses coal with an ash content of 19% and a ating value of 24,000 kJ/kg. Assume 28% of the ash content goes up the stack as particulate matter in the flue gas e PM emission is controlled by an ESP which has the following efficiencies and weight distribution in the given siz ges. Find the fly ash emitted in g/s. size efficiency (%) wt% in flue gas 0-5 70 7 5-10 92.5 19 10-20 96 21 20-40 99 24 >40 100 29

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

for R600a1) at 40oC what is the pressure of condensation?2) What is the absolute pressure and gauge pressure of -25’C evaporating refrigerant? 3) mollier diagram (including dryness)
Show all elements of your design including an explanation of assumptions made and justify your design decisions for the problem: When heating up a cold stream (5000 kg/h water) from 40ᵒC to 90ᵒC while cooling down a hot stream (5000 kg/h water) from 110ᵒC to 60ᵒC in AES exchangers, how many shells do you need?
What is the specific refrigerant that meed for refrigeration and cryogenic plant for liquid oxygen production? (ex. R134a, not a nitrogen answer please)
A Rankine cycle is executed with steam expanding initially from 20 MPaa and 100 deg SH.Condensation occurs at 300 mm HG vac. All expansion and compression efficiencies are 90 %.Sketch the equipment layout and the TS diagram. ANSWER THE GIVEN QUESTION Wnet (actual) = 9402.4 Qs (actual) = 27595.4
Hello could anyone teccomend any improvements to thid type of rankie cycle combustion chamber fuel HRSG condenser Figure 1. Combined cycle gas turbine (CCGT) system
2. (#47ppS-37TrD) - A water tube boiler evaporated 6.05 kg of water per sec from a feed water temperature of 104.44 deg C to steam at 1241 kPa and quality of 0.97, weight of coal fuel per sec 0.57 kg, high heat value of the coal as fired, 11,800 Btu/lb Steam Properties: At 104.44 deg C hf At 1241.1 kPa = 437.78 (interpolated) h₁ = 805.29 = hg 1980.6 (interpolated) a) Determine the rate of heat absorption in kJ/kg
I need the answer as soon as possible
5. Steam is generated at 6.10 MPa and 4500C and condensation occurs at 170 kPa. (a)For a Rankine engine operating between these limits, compute the thermal efficiency and the heat rate. (b) Considering that a Rankine cycle occurs between the limits, determine QA, QR, WNet, and eC. (c) What mass flow rate is required for a net output of 35 MW? Please answer what is asked in a, b and c. Thanks
A reheater cycle with two stages of reheating is executed with steam expandinginitially from 20.544 Mpa and 540oC. The pressures of two reheaters are 3.2544 Mpaand 0.85544 Mpa, and the steam leaves each reheater at 540 oC. Condensation occursat 70 oC. Calculate W, ec and ee.
9. When developing a certain power, the specific fuel con- sumption of an internal combustion engine is 0-255 kg/kWh (brake) and the mechanical efficiency is 86% Calculate (i) the indicated thermal efficiency, and (ii) the brake thermal efficiency, taking the calorific value of the fuel as 43-5 MJ/kg. If 35 kg of air are supplied per kg of fuel, the air inlet being at 26°C and exhaust at 393°C, find (iii) the heat energy carried away in the exhaust gases as a percentage of the heat supplied, taking the specific heat of the gases as 1-005 kJ/kg K.
first three already answered
I need the answer as soon as possible