Lab Report On Methylcyclohexene

This way, cyclohexane is converted to adipic acid or hexanedioic acid. Since the product is soluble in hot water, the two-phase systems (organic cyclohexane and aqueous hydrogen peroxide) slowly become a single aqueous phase. In the end, only H2O2 and cyclohexene can be changed, tungstate and the phase transfer catalyst can be tapped and reused. The phase transfer catalyst used were a mixture of aliquat 336 and potassium hydrogen sulphate.

14 mL of 9 M H2SO4 was added to the separatory funnel and the mixture was shaken. The layers were given a small amount of time to separate. The remaining n-butyl alcohol was extracted by the H2SO4 solution therefore, there was only one organic top layer. The lower aqueous layer was drained and discarded. 14 mL of H2O was added to the separatory funnel. A stopper was placed on the separatory funnel and it was shaken while being vented occasionally. The layers separated and the lower layer which contained the n-butyl bromide was drained into a smaller beaker. The aqueous layer was then discarded after ensuring that the correct layer had been saved by completing the "water drop test" (adding a drop of water to the drained liquid and if the water dissolves, it confirms that it is an aqueous layer). The alkyl halide was then returned to the separatory funnel. 14 mL of saturated aqeous sodium bicarbonate was added a little at a time while the separatory funnel was being swirled. A stopper was placed on the funnel and it was shaken for 1 minute while being vented frequently to relieve any pressure that was being produced. The lower alkyl halide layer was drained into a dry Erlenmeyer flask and 1.0 g of anhydrous calcium chloride was added to dry the solution. A stopper was placed on the Erlenmeyer flask and the contents were swirled until the liquid was clear. For the distillation

Alcohol dehydrations are widely used in many industries to produce alkene. In this experiment 2-methylcyclohexanol was dehydrated to three possible products using phosphoric acid as a catalyst. The main tool for this experiment is the Hickman still. First, Drierite was added to the Hickman still so that any excess water formed during the experiment will be absorbed. It also acted as a boiling stone and addition surface to increase surface area. Next, 0.75 mL of 2-methylcyclohexanol is added to the still and right after 1 mL of phosphoric acid is added. The phosphoric acid (H3PO4) acts as a catalyst in order for the reaction to occur. The mixture is heated up to between 120o Celsius and 160o Celsius. If the temperature goes above 165oC then

1. Purpose: to clarify the mechanism for the cycloaddition reaction between benzonitrile oxide and an alkene, and to test the regiochemistry of the reaction between benzonitrile oxide and styrene.

This experiment was designed by conducting a substitution reaction to construct a complex compound (2-methylphenoxyacetic acid) from two simple parts; also known as synthesis - converting simple molecules into more complex molecules. A purification technique known as crystallization was used to purify the product. Suction filtration was used to filter out the product. The experiment was completed over a three-day experimental period.

The purpose of this lab was to carry out a dehydration reaction of 2-methylcyclohexanol by heating it in the presence of phosphoric acid and determining which alkene product would be the major product. Methylcyclohexanols were dehydrated in an 85% phosphoric acid mixture to yield the minor and major alkene product by elimination reaction, specifically E1. The alkenes were distilled to separate the major and minor products and gas chromatography was used to analyze the results and accuracy of the experiment. The hypothesis was the major product of the reaction would be the most substituted product. This conclusion was made because of

Yield: Assuming a reaction that uses up 100% of the cyclohexanone reagent, the theoretical yield is 2.32g. This could be calculated using the following calculation. The 1:1 ratio of moles cyclohexanone to moles bisphenol Z comes from the mole ratio in the reaction scheme.

Distillation is a method of separating two volatile chemicals on the basis of their differing boiling points. During this lab, students were given 30 mL of an unknown solution containing two colorless chemicals. Because the chemicals may have had a relatively close boiling point, we had to employ a fractional distillation over a simple distillation. By adding a fractionating column between the boiling flask and the condenser, we were able to separate the liquids more efficiently due to the fact that more volatile liquids tend to push towards the top of the fractionating column, thereby leaving the liquid with the lower boiling point towards the bottom. After obtaining the distillates, we utilized a gas chromatograph in order to analyze the volatile substances in the gas phase and determine their composition percentage of the initial solution. Overall, through this lab we were able to enhance our knowledge on the practical utilization of chemical theories, and thus also demonstrated technical fluency involving the equipment.

Dispense .5 mL water into the already weighed conical vial, replace cap and face insert on its down side.

To prepare and purify an ester: 1-pentyl ethanoate, using pent-1-ol and ethanoic acid. An annotated reaction showing this reaction is shown below:

An ester was synthesized during an organic reaction and identified by IR spectroscopy and boiling point. Acetic acid was added to 4-methyl-2-pentanol, which was catalyzed by sulfuric acid. This produced the desired ester and water. After the ester was isolated a percent yield of 55.1% was calculated from the 0.872 g of ester recovered. This quantitative error was most likely due to product getting stuck in the apparatus. The boiling point of the ester was 143° C, only one degree off from the theoretical boiling point of the ester 1,3-dimethylbutyl, 144 ° C. The values of the

For this experiment, Alcohol D and Acid 2 reacted in the presence of concentrated sulfuric acid, resulting in a colorless solution with brown layer on top. After washes with sodium bicarbonate and brine, the pale-yellow liquid product was dried and then distilled. Distillation resulted in two colorless fractions, the second of which had a boiling point of 69-70 ˚C. This boiling point is unrealistic for any compound obtained in this experiment, so it was not used in identifying the product. After distillation, both fractions were spectroscopically analyzed. The IR and NMR spectra obtained for both fraction were identical, meaning both fractions contained exactly the same substance. Both fractions also smelled the same, like piña colada, therefore confirming this conclusion. This outcome also meant that the amount of product synthesized was 5.7393 g.

The purpose of this lab was to synthesize the ester isopentyl acetate via an acid catalyzed esterification (Fischer Esterification) of acetic acid with isopentyl alcohol. Emil Fischer and Arthur Speier were the pioneers of this reaction referred to as Fischer Esterification. The reaction is characterized by the combining of an alcohol and an acid (with an acid catalyst) to yield and ester plus water. In order to accomplish the reaction, the reactants were

An ice bath was prepared in a large beaker and a small cotton ball was obtained. 0.5 g of acetanilide, 0.9 g of NaBr, 3mL of ethanol and 2.5 mL acetic acid was measured and gathered into 50mL beakers. In a fume hood, the measured amounts of acetanilide, NaBr, ethanol and acetic acid were mixed in a 25mL Erlenmeyer flask with a stir bar. The flask was plugged with the cotton ball and placed in an ice bath on top of a stir plate. The stir feature was turned on a medium speed. 7mL of bleach was obtained and was slowly added to the stirring flask in the ice bath. Once all the bleach was added, stirring continued for another 2 minutes and then the flask was removed from the ice bath and left to warm up to room temperature. 0.8mL of saturated sodium thiosulfate solution and 0.5mL of NaOH solution were collected in small beakers. The two solutions were added to the flask at room temperature. The flask was gently stirred. Vacuum filtration was used to remove the crude product. The product was weighed and a melting point was taken. The crude product was placed into a clean 25mL Erlenmeyer flask. A large beaker with 50/50 ethanol/water

In this experiment, methyl benzoate was synthesized from benzoic acid and methanol with acid catalyze using Fisher Esterification. First benzoic acid and methanol were mixed in 100 mL round bottom flask. We cooled the mixture in ice and poured 3 mL of conc. H2SO4 and swirled to mix compounds. Then we refluxed the mixture for 1 hour. We let the solution cool and then decanted into a separatory funnel containing 50 mL of water and rinsed the round bottom flask with 35 mL of tert-butyl methyl ether and added that to a separatory funnel. We shook and vented thoroughly and drained the aqueous layer which contained a bulk of methanol and H2SO4. We washed the solution in the separatory funnel with 25 mL of water, followed by 25 mL of sat. sodium bicarbonate