Active Learning Experience 10_Thanksgiving Media

To answer the question, type your answers in RED or paste the image of your handwriting solution   Given the circuit #1 presented above, answer the following questions:   Determine the value of the VD (voltage forward of the LED) for the LEDs RED, VDRED, GREEN, VDGREEN and BLUE, VDBLUE, when the current through the LEDs is 10mA,   VDRED = ____________ ; VDGREEN = ____________ ; VDBLUE = ____________   Is the LED in Circuit #1, connected in the way that will be lighting up or not – Justify your answer   Type your answer here     Calculate the value of the resistance Rled in Circuit #1, to ensure that a RED LED will have a current of 10 mA Type your answer here or paste the image of your handwriting solution here     Calculate the value of the resistance Rled in Circuit #1, to ensure that a GREEN LED will have a current of 10 mA Type your answer here or paste the image of your handwriting solution here     Calculate the value of the resistance Rled in Circuit #1, to ensure that…

List all the tools and materials for terminating, connecting and testing electrical wiring and electronics circuits to be use in computers. *Please draw a table for the tools and materials with three columns where Terminating, Connecting, and Testing are indicated. Thank you and God bless!

Question were attached in photo. Refer to the attach photo below. Thanks

You should clearly indicate the position ofton this sketch.(               need only handwritten solution .otherwise downvote.)

______________1.      It is the ability of an electronic part to meet the required performance specifications in its life cycle application environment for a specified period. ______________2.      It evaluates the performance and operating specifications of electronic components within the set standards. ______________3.     It is the ability to detect and assess the errors in the system.

Messages AA Statement one Training will allow you to safely erect a mobile. tower scaffold on any ground surface condition. and access the tower both internal and externally Statement two In windy conditions placing sheeting around the mobile tower scaffold will protect the workers on the tower a) Statement two is incorrect b) Statement one and two are correct c) Statement one is correct and statement two is incorrect d) Both statements are incorrect actclass.co.uk 22 Questi 23 Questi 24 Questi 25 Questi 26 Questi Submit Answers Ć

DO NOT COPY FROM OTHER WEBSITES ( else will be reported to bartleby team) Upvote guarenteed for a correct and detailed answer. Thank you!!

Select the correct term to complete the statement. ( both images are shown below)

Direction. Answer each problem and show your solutions cleanly and clearly. Draw diagrams._______________________________________________________________________________________________________________________

#10.  Pls answer correctly. Need another answer from diff expert. :)

Please help answer the questions about the block diagram shown below. Thank you!

___________ is an Area on a device characteristic where the ratio between applied voltage and resulting current is constant.

______________1.      It checks the ability or range of operations of the electronic components that be run in the system. ______________2.      It assesses the ability of the electronic components to exchange information or can access data without any restriction. ______________3.      It evaluates the ability of the part to meet the functional, mechanical, and electrical performance requirements.

Select the letter of the correct answer from the given problem. *Kindly provide a CLEAR and COMPLETE solution* (Answer should be typewritten)

Schedule of Loads and Basic Calculation — Create a tabulated load schedule of your home.

f.1. Since the footing or foundation is generally part of the grounding electrode system, the _______electrode is one of the first electrodes installed.A. metal water pipeB. plateC. concrete-encasedD. ground ringf.2. When you're connecting the grounding electrode conductor to a metal water pipe as it enters a building,the connection must be made within _______ feet of the pipe's entrance to the building.A. 10B. 5C. 15D. 7f.3. Which National Electrical Code table is used for sizing grounding electrode conductors?A. Table 250.102(C)(1)B. Table 250.66C. Table 250.122D. Table 250.118(6)(a)

*************************SUBJECT = SIGNALS AND SYSTEMS***********************

a) Write down and prove DeMorgan's theorem. b) Remove the following complements using DeMorgan's theorems. ______________________           _________________                   _____________ P+ Q + (C+D.E').  (F+G)

Give me about ten examples of electrical code violations in maintenance and repair. Hopefully the explanation is detailed and better if there is a picture with references.

Answer the following: A) Type of clipper circuit per level of clipping. 1. ___________ 2. ___________ 3. ___________   B) Type of clipper circuit per non-linear devices used. 1. ___________ 2. ___________   C) Other term for clipper circuit. 1. ___________ 2. ___________ 3. ___________

If an electrical system operates at a potential higher than 600 volts, the nonmetallic conduit must be encased in at least_of concrete. A. 1 inch B. 2 inches C. 4 inches D. 6 inches

Electrical Engineering Give correct answer     UPSs measured in ____________ and ______________. __________________ are what your system uses and ____________________________ are what UPS can deliver in a perfect world.

Fill in the blanks with the resistor colors that correspond to the values.

TOPIC: Power Systems, Power Plants & IlluminationINSTRUCTIONS:- Answer in this format: Given, Illustration, Required Conversion, Solution, Final Answer.- Step-by-step solution, do not skip even simple calculations to avoid confusion.- If answered in written form, make sure it is readable.PROBLEM:In hazardous locations, the use of non-metallic conduit shall be permitted provided it is buried NOT less than ___________ blow the earth level. 400 mm 600 mm 1000 mm 500 mm

QUESTION 9 When a ground wire is connected to an interior gas piping system and the underground portion of the gas pipe into the building is plastic, which of the following is (or are) true? a   A.This would be approved by code as the gas pipe is only being bonded to the electrical system. b   B.This installation would be approved by code, as the gas pipe is not a grounding electrode. c   C.Both A and B d   D.Neither A nor B

# Solve the whole question in pen and paper. Thank you!!

Please help me with my laboratory activity. Thanks a lot!

Explain each option & Choose the correct option. 4) The _ calculated load is rarely placed on an electrical system.A. optionalB. standardC. total 5) What's the primary disadvantage of using copper conductors?A. CostB. AvailabilityC. Weight 6) You're evaluating the components of a multioccupancy building that won't have an on-site employee. To be compliant with the NEC, each occupant will need to have access to their ownA. service-disconnecting means.B. service conductor.C. cable attachment point.D. emergency fire water pump disconnect ..

16.a. When installing cable behind a wall, it's recommended to run the cable behind the baseboard rather than through the studs when the A. fish tape can't be utilized. B. wall is plasterboard. C. wall studs are less than 16 inches apart. D. wall is plaster or lath.  16.b. A device box with supports is the best choice when installing a A. device box mounted in an existing drywall-covered wall. B. device box in a lath ceiling. C. device box that's to be attached to a bar hanger. D. shallow device box in either new or existing walls.