_02

Calculate the assigned values in the circuits below.       E2 = ________            E3 = _________          E6 = _________          E9 = _________ E11 = ________           E13 = _________         RT = ________            R6 = __________ IT = _________           I5   = __________        I7 = _________           I10 = __________ PT = ________

KVLLoop abfea: __________________________________________________Loop cdhgc: __________________________________________________Loop bcgfb: ___________________________________________________

Direction. Answer each problem and show your solutions cleanly and clearly. Draw diagrams._______________________________________________________________________________________________________________________

Electrical Engineering Give correct answer     UPSs measured in ____________ and ______________. __________________ are what your system uses and ____________________________ are what UPS can deliver in a perfect world.

f.1. Since the footing or foundation is generally part of the grounding electrode system, the _______electrode is one of the first electrodes installed.A. metal water pipeB. plateC. concrete-encasedD. ground ringf.2. When you're connecting the grounding electrode conductor to a metal water pipe as it enters a building,the connection must be made within _______ feet of the pipe's entrance to the building.A. 10B. 5C. 15D. 7f.3. Which National Electrical Code table is used for sizing grounding electrode conductors?A. Table 250.102(C)(1)B. Table 250.66C. Table 250.122D. Table 250.118(6)(a)

Answer the following: A) Type of clipper circuit per level of clipping. 1. ___________ 2. ___________ 3. ___________   B) Type of clipper circuit per non-linear devices used. 1. ___________ 2. ___________   C) Other term for clipper circuit. 1. ___________ 2. ___________ 3. ___________

___________ is an Area on a device characteristic where the ratio between applied voltage and resulting current is constant.

13. If an equipment bonding jumper is run external to a raceway, it must be less than _______ feet.A. 6B. 2C. 4D. 5

With the top view as the reference, the current going out of the page is ________ while the current going into the page is ________.

Answer each problem and show your solutions cleanly and clearly. Draw diagrams.__________________________________________________________________________________________________________

To answer the question, type your answers in RED or paste the image of your handwriting solution   Given the circuit #1 presented above, answer the following questions:   Determine the value of the VD (voltage forward of the LED) for the LEDs RED, VDRED, GREEN, VDGREEN and BLUE, VDBLUE, when the current through the LEDs is 10mA,   VDRED = ____________ ; VDGREEN = ____________ ; VDBLUE = ____________   Is the LED in Circuit #1, connected in the way that will be lighting up or not – Justify your answer   Type your answer here     Calculate the value of the resistance Rled in Circuit #1, to ensure that a RED LED will have a current of 10 mA Type your answer here or paste the image of your handwriting solution here     Calculate the value of the resistance Rled in Circuit #1, to ensure that a GREEN LED will have a current of 10 mA Type your answer here or paste the image of your handwriting solution here     Calculate the value of the resistance Rled in Circuit #1, to ensure that…

Find the value of unknown. 3:1 — 6:____

Question 9 An FET is a current voltage O voltage and current __-controlled device.

An enclosure, constructed so that moisture will not enter the enclosure under specific test conditions, is called “____”

Assignment on Threaded jointsDue date:__________________ ___________________ ________________ Surname Given names IDA power line tower is erected to support a high-voltage power line (see figure below),which includes six phase conductors and three Earth shield wires. The tower isfabricated as a steel structure resting on four square supporting feet bolted to aconcrete foundation with four Anker bolts at each support (see figure below). Theresultant tension force FT from cables on each side of the tower is applied at point m,and can be at 60o to the horizontal plane (sagging downwards) if the tower is installedon a plane or at 30o to the horizontal plane pointed upwards if the tower is installed on ahilly landscape. The gusty wind load, which could be represented with a resultant forceof Fw is applied at the geometric centre of the tower n in any direction in the horizontalplane (see figure below) and tends to shift the tower sideways and topple it. In the caseof an accident when all…

Find the value of unknown. 2:5 —___:15

Req =_______________ Ceq=________________ Leq=________________

If a recessed  luminary without an integral junction boxes installed what extra wiring must be provided

6.a. Extreme _______ may cause some nonmetallic conduits to become brittle and therefore moresusceptible to damage from physical contact.A. coldB. corrosionC. voltageD. heat6.b. Snap switches are permitted to be grouped or ganged in an enclosure provided the voltage between theadjacent snap switches does not exceed ___ V.A. 400B. 300C. 200D. 100

2. Imagine that you're asked to install an auxiliary grounding electrode at the base of a lighting pole in aparking lot. This auxiliary grounding electrode will be connected to theA. lighting pole's electrical service equipment grounding conductor.B. electrical service's grounding electrode conductor.C. next lighting pole's auxiliary grounding electrode.D. lighting pole's neutral conductor.

On site plans, all evevations are referenced from_. A. The centerline of a street B. Ground level C. A bench mark D. A test boring

______________1.      It checks the ability or range of operations of the electronic components that be run in the system. ______________2.      It assesses the ability of the electronic components to exchange information or can access data without any restriction. ______________3.      It evaluates the ability of the part to meet the functional, mechanical, and electrical performance requirements.

1.1 PV modules can be wired together in an array using ______ connections to increase voltage. a. Terminating b. Series c. Parallel d. AC 1.2 A PV module, also called a solar panel, is comprised of individual photovoltaic _______ wired and mounted together as an integrated unit. a. Capsules b. Compartments c. Chips d. Cells   1.3 A __________ system uses a storage system that stores the generated electricity so it can provide during times when the system’s panels are not receiving solar energy. a. Direct coupled b. Self regulating c. Charge controlled d. Indirectly connected   1. 4 __________ energy may have the potential to supply all of the world's energy needs, but at this time, it provides a very small percentage. a. Coal b. Natural Gas c. Diesel d. Solar

QUESTION 9 When a ground wire is connected to an interior gas piping system and the underground portion of the gas pipe into the building is plastic, which of the following is (or are) true? a   A.This would be approved by code as the gas pipe is only being bonded to the electrical system. b   B.This installation would be approved by code, as the gas pipe is not a grounding electrode. c   C.Both A and B d   D.Neither A nor B

Question 6 B  Thevenin’s Theorem RL what VTH RTH Full explain this question very fast solution sent me step by step Not:- Text typing work only and Don't ignore any part all part work u

It is measure of how much counter emf is generated in a circuit. ________