CS 4407 S5 p4

K1=   K2=   Note:   Round off your final answer to the nearest ten thousandth. Take note: Only the final answer should be rounded off. Always write the answer with 4 decimal places, (i.e, 4.25 should be written as 4.2500) EXCEPT for whole numbers.

Ohm's law experiment, we calculated and measured using multitester the resistor,voltage and current. Our datas incluse theoretical and experimental. What do you think are the possible causes or sources of laboratory errors from the data? Do these errors make your data smaller or larger? Why?

Please answer fast I'll rate you

I need only part C only

A Moving to another question will save this response. Question 1 If BJT is operated in saturation region, it will act as a closed switch. O True False A Moving to another question will save this response.

1.17 Test data from four components are given below. Each test consists of a complete traversal from an input value of 0 to an input value of 25. The data are listed in the order in which the traversal was made. Plot the data from each test on an input/output graph with the input on the horizontal axis and the output on the vertical axis. Use ar- rows to show the direction of traversal. 1.18 Identify all nonlinearities exhibited by each compo- nent in Exercise 1.17. Component 1 Input 0 5 10 15 20 25 20 15 10 50 Output 0 16 38 62 84 100 84 62 38 16 0 Component 2 Input 0 5 10 15 20 25 20 15 10 50 Output 0 18 36 56 78 100 82 64 44 22 0 Component 3 Input 0 6 10 15 20 22 25 19 15 10 5 30 Output 10 10 30 55 80 90 90 90 70 45 20 10 10 Component 4 Input 0 6 10 15 20 22 25 19 15 10 5 3 0 Output 10 10 27 50 78 90 90 90 73 50 22 10 10

5. Assume that you need to measure an average temperature in a heated space. You have three identical temperature sensors. Each sensor produces a voltage proportional to tempcrature such that: Sensor Voltage = .01 * Temperature in degrees Celsius Assume that you have three voltages, Va, V, and Ve You want to take the average of these three voltages lin order to compute the average temperature inside the heated space. This circuit has been suggested as a possibility for computing the average. Rf Vout Ve A. Find an analytical cxpression for Vout, in terms of the input voltages and the four resistors. B. Determine if a proper choice of resistors will let you use this as an averager. If you can, then findi some appropriate values for the resistors.

Content: Analyze and explain further the step by step answer. Thank you.

I need the answer as soon as possible

A person is recording measurements from an analog data reader. During the first reading, he was not looking at the meter from a straight angle. He gets the reading of 72. At a second reading later he looks straight at the machine and gets the reading of 70. a) Which reading number is nearer to the actual value? What is the error type that happened in that reading? b) c) Suppose the data reader becomes faulty due to the extreme heat and gives a third measurement of 65. What type of error happened now? The data reader is working properly now, but there is a slight difference between two readings for the same measure. What type of error happened now and how can we d) minimize it?

The subject is Power Electronics and Power Systems Please send the answer by typing ONLY. I don't want any handwritten. Show All Answers Steps. Also, don't copy-paste from the net, as plagiarism will be counted.   Q-01 (What is called Buck Converter & What is called Boost Converter?)  give two examples for each.

The subject is Power Electronics and Smart Power System  Please send the answer by typing i don't want any handretten. Also, don't copy past from net as plagiarism will be counted.

i need ans within 9 minutes with draw happy emoji in the end my best wishes ton

Please send the answer by typing only. I don't want handwritten.  The subject is ( Electronic Circuits ) Q4) Give the drain current equation of JFET.

Question Ach calculate the decimal equivalent of the hexadecimal number 3AE2 .Show proper steps and calculation.. .Full explain this question and text typing work only     We should answer our question within 2 hours takes more time then we will reduce Rating Dont ignore this line .

Task 3-b: If you have two instruments used to measure the temperature of two points inside the factory (point A and point B). The true temperature for point A is 25 C, while the true temperature for point B is 30. However, the measured values for the first instrument were 26 and 30, while for the second instrument, the measured values were 25 and 29. i) Define using your own words the sensitivity drift and bias drift, then explain how these types of error could affect the measured values of the sensors. ii) of these two instruments against different temperature values (between 0 – 100 C). Assume Analyze the accuracy and error for both instruments by calculating and plotting the response linear relationship between the input and output for these instruments. Based on your calculations, specify the type of drift that affects each sensor (sensitivity drift, bias drift, or both). iv) Which of these error types can be corrected using calibration?

INFE242 ELECTRONICS PLEASE MAKE SURE THE ANSWER IS CORRECT And make your Line clear ?? All thank and appreciation ?? ?

Do not copy from other websites Correct and detailed answer will be Upvoted else downvoted. Thank you!

Compute for the Equivalent Resistance of Terminal RBD. Show complete solutions. Strictly use stored values in the computations. Final answers must be written up to fourth decimal place.

I need the answer as soon as possible

Pls help.me answer the following, show neat and whole solution and kindly send a screenshot of simulation.

subject DLD plzz solve urgent with complete details thnx

What is the right answer for part D

Q1 (a) PROTON development department wants to design an embedded safety warning system that able to monitor child seat belt condition in their upcoming vehicle launch. There are THREE independent sensors input labeled as X, Y and Z to produce THREE outputs signal of R, S and T. Sensor X was embedded at bottom seat and sensor Y was assigned at headrest support. While sensor Z was assign at buckle clip. All sensor produces HIGH when pressed or tug in. Output R will be HIGH when both input X and Y is HIGH. Output S will be HIGH when input Z and output R is HIGH. Output T will be HIGH when output R is LOW but output Z is HIGH. (i) Construct the truth table for this circuit. (ii) Analyze the minimize logic equations for output R, S and T. Show using both Karnaugh map and Boolean expression to simplify the expressions. (iii) Using the simplified expression from question Q1(a)(ii), draw its combinational circuit response.

i need the answer quickly

Soru 1 Find V1, V2 and Ix using mesh analysis. If you use any other method, the answer will not be 2 Henüz graded. cevaplanmadı Uygulam 25,00 üzerinden Kalan sü işaretlenmiş P Soruyu işaretle 7002 I V1 V2 3002 5A 902 30Ω ) 15A

Calculate the IT, RT, and PT. (Show the correct answer, and all thesyep by step solutions. Do not skip all the solutions.)

report.The report should cover the followings1. Name of the experiment2. Objective3. Required Components and Equipments4. Experimental Setup (i.e., diagram of the circuit)J. Results and DiscussionsDraw a circuit diagram which will compare three 4 bit numbers. You haveMagnitude Comparators and 2:1 MUXs.   plz attach the proteus file

None