Report 9_ Shahd Ahmed

.pdf

School

Rutgers University *

*We aren’t endorsed by this school

Course

160:251

Subject

Chemistry

Date

Jan 9, 2024

Type

pdf

Pages

Uploaded by MinisterStarGoldfinch36

Shahd Ahmed Report 9: Gravimetric Analysis of Chloride and Sulfate Abstract : In this experiment, the concentration of Cl- in seawater was estimated to be 11939.333 mg/L, 321.364 mM, and 1.171% by mass. The concentration of SO42- in the first trial is determined to be 2966.667 mg/L, 30.884 mM, and 0.284% by mass. In the second trial, the SO42 concentration is 2360 mg/L, 26.205 mM, and 0.225% by mass. Introduction : Using Gravimetric Analysis, the concentration of chloride and sulfate ions could be determined in a seawater sample. Using techniques such as filtration, pipetting, and dehydrating the precipitate from the seawater solutions allowed the concentration of Cl- and SO42- to be determined. Experimental Methods : Part 1 - Separation of chloride and sulfate by anion exchange Weigh a clean 50 mL beaker, take a 1.5 mL sample of filtered seawater, and transfer it to the beaker, weighing it again. Using an anion exchange column, drain the liquid into a flask underneath until the liquid is 2-3 millimeters above the resin bed. Transfer 5mL of 0.5 M NaNO3 solution into the column to check for chloride ions. Adjust the solution rate to 20 drops a minute and let the column drain until 1 mL of the 5 mL added remains. Replace the collection beaker with a clear test tube and collect the last mL, leaving 2-3 millimeters above the resin bed. Test the eluate for the presence of Cl- by adding a few drops of 0.2 M AgNO3 and looking for a white precipitate. If a precipitate forms, add 5 mL of 1.0 M NaNO3 to the column and collect the last mL of eluent. Once there is no precipitate, place a 250 mL Erlenmyer flask under the column and carefully load the previously weighed 1.5 mL sample of seawater. Rinse the beaker with 1-2 mL of 0.5 M NaNO3 solution and transfer the entire solution. Allow the liquid to drain through the column until the resin is covered by 2-3 mm of liquid. Attach a plastic funnel to the column's opening and slowly add 60 mL of 0.5 M NaNO3 solution to the funnel. Allow the solution to run through the column for 60 minutes, and begin working on part 3. Once 1 mL of the eluent is left in the column, stop the flow and collect the last milliliter in a test tube. Add a few drops of AgNO3 to see if precipitate forms. Cover the test tube in foil away from sunlight if a precipitate is present, and place the Erlenmyer flask back under the column. Repeat the process and add 15 mL more of the 0.5 M NaNO3 solution to the column until there is no precipitate.

Shahd Ahmed Report 9: Gravimetric Analysis of Chloride and Sulfate Part 2 - Quantitative gravimetric determination of chloride To a sulfate-free sample, which is 50 mL of eluate, add 8.0 mL of 0.2 M AgNO3 solution. Shield the flask from sunlight, as precipitation should occur while swirling the flask, and place the flask in the oven for 20 minutes. After 20 minutes, let the flask cool down, then add a few drops of 0.2 M AgNO3 solution to test for completeness of precipitation. If additional precipitation occurs, add 1 mL of 0.2 M AgNO3 solution. Set up a filtration apparatus with a clean collecting flask underneath. Obtain and weigh a Fisher MCE membrane filter, then place it in the filtration apparatus. Add 1 mL of DI water on top of the filter, then transfer the AgCl precipitate using two 5 mL portions of 0.01 M HNO3 on the walls of the flask. Turn on the vacuum in the aspirator and filter. Once filtered, discard the waste solution properly and rinse the precipitate with 2 mL of 0.01 M HNO3 and aspirate. Add a few drops of 0.1 M NaCl solution and look for precipitate; if precipitate occurs, add 5 mL of 0.01 M HNO3. Allow precipitate on the filter to air dry for 2-3 minutes with aspiration on, then place the filter in over for 60 minutes. After 1 hour, remove the sample from the oven and weigh it. Part 3 - Separation of chloride and sulfate by selective precipitation Prepare two identical samples, weigh 50 mL, transfer 1.5 mL of filtered seawater, and weigh the beaker again. Add 4-5 mL of Di water and 2 mL of 0.06 M Ba(NO3)2 in 0.01 M HNO3 to the beaker. Swirl the flask and let the precipitate stand for 15-20 minutes for both samples. Part 4 - Gravimetric determination of sulfate Weigh a 0.45 um membrane filter and place it into an assembled filtration apparatus. Place a clean receiving flask under and transfer each seawater sample separately with 4-5 mL of 0.01 M HNO3; filter with aspiration. Rinse the precipitate with 4-5 mL of 0.01 M HNO3. Allow the filter to dry for 2-3 minutes with the aspirator on, then place into the oven for 15-20 minutes. Once dry, weigh the filter paper for each seawater sample. Results : Table 1: Mass of seawater used in the sample

Shahd Ahmed Report 9: Gravimetric Analysis of Chloride and Sulfate Table 2: Quantitative Gravimetric determination of Chloride Molar Mass(AgCl): 143.32 g Molar Mass (Cl): 35.453 g Literature value of Cl concentration is 18,900 mg/L. Sample calculation for mg/L : Sample calculation for mmol/L : Sample calculation for mass% : Comparison with literature value of Cl - concentration : The concentration of Cl- in seawater, according to Lenntech, should be 18,900 mg/L. However, my calculations determine the concentration to be 11,939.333 mg/mL. The percent error between the two concentrations is 36.095%, and my calculated concentration could be lower based on human error. During the experiment, circumstances such as not retrieving all the precipitates from the flask when weighing the filter paper or not leaving the filter paper in the oven long enough could have caused my concentration of Cl- to be lower than the Lenntechs value of Cl- in seawater.

Your preview ends here

Eager to read complete document? Join bartleby learn and gain access to the full version

Access to all documents
Unlimited textbook solutions
24/7 expert homework help

Recommended textbooks for you

Chemistry & Chemical Reactivity

Chemistry

ISBN:9781337399074

Author:John C. Kotz, Paul M. Treichel, John Townsend, David Treichel

Publisher:Cengage Learning

Chemistry & Chemical Reactivity

Chemistry

ISBN:9781133949640

Author:John C. Kotz, Paul M. Treichel, John Townsend, David Treichel

Publisher:Cengage Learning

Introductory Chemistry For Today

Chemistry

ISBN:9781285644561

Author:Seager

Publisher:Cengage

Chemistry: The Molecular Science

Chemistry

ISBN:9781285199047

Author:John W. Moore, Conrad L. Stanitski

Publisher:Cengage Learning

Chemistry: Principles and Practice

Chemistry

ISBN:9780534420123

Author:Daniel L. Reger, Scott R. Goode, David W. Ball, Edward Mercer

Publisher:Cengage Learning

Chemistry

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Cengage Learning

SEE MORE TEXTBOOKS

Recommended textbooks for you

Chemistry & Chemical Reactivity
Chemistry
ISBN:9781337399074
Author:John C. Kotz, Paul M. Treichel, John Townsend, David Treichel
Publisher:Cengage Learning
Chemistry & Chemical Reactivity
Chemistry
ISBN:9781133949640
Author:John C. Kotz, Paul M. Treichel, John Townsend, David Treichel
Publisher:Cengage Learning
Introductory Chemistry For Today
Chemistry
ISBN:9781285644561
Author:Seager
Publisher:Cengage
Chemistry: The Molecular Science
Chemistry
ISBN:9781285199047
Author:John W. Moore, Conrad L. Stanitski
Publisher:Cengage Learning
Chemistry: Principles and Practice
Chemistry
ISBN:9780534420123
Author:Daniel L. Reger, Scott R. Goode, David W. Ball, Edward Mercer
Publisher:Cengage Learning
Chemistry
Chemistry
ISBN:9781305957404
Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste
Publisher:Cengage Learning