Answered: What is the gauge pressure in atm at…

Name: MReview I Constants(Figure 1) shows a syringe filled with 20° C olive
Uploaded: 2024-03-20T06:51:10.000Z
Channel: Bartleby
Description: MReview I Constants(Figure 1) shows a syringe filled with 20° C olive oil.Part AWhat is the gauge pressure in atm at point P, where the needle meets the wider body of the syringe? The pressureat the exit of the needle is 1.0 atm.Express your answer

Science

Physics

What is the gauge pressure in atm at point P, where the needle meets the wider body of the syringe? The pressure at the exit of the needle is 1.0 atm. Express your answer in atmospheres.

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter15: Fluids

Section: Chapter Questions

Problem 11PQ: Suppose you are at the top of Mount Everest and you fill a water balloon. The air pressure at the...

See similar textbooks

Similar questions

(a) Using Bernoulli's equation, show that be measured fluid speed v for a pitot tube, like the one in figure 14.32(b), is given by v=( 2gh)1/h , where h is be height of be manometer fluid, p' is the density of the manometer fluid, p is the density of the moving fluid, and g is be acceleration due to gravity. (Note that v is indeed proportional to the square root of h, as stated in text) (b) Calculate v for moving air if a mercury manometer's h is 0.200 m. Figure 14.32 Measurement of fluid speed on Bernoulli’s principle. (a) A manometer is connected to two tubes close together and small enough not to disturb the flow. Tube 1 is open at the end facing the flow. A dead spot having zero speed is created there. Tube 2 has an opening on the side, so the fluid has a speed v across; thus, pressure there drops. The difference in pressure at the manometer is 12v22 , so h is proportional to . 12v22 (b) This type of velocity measuring device is a Prandtl tube, also known as a pitot tube.
Considering the magnitude of typical arterial blood pressures, why are mercury rather than water manometers used for these measurements?
A container of water has a cross-sectional area of A=0.1m2 . A piston sits top of the water (see be following figure). There is a spout located 0.15 m from the bottom of tank, open to the atmosphere, and a stream of water exits the spout. The cross sectional area of the spat is As=7.0104m2 . (a) What is the velocity of the water as it leaves the spout? (b) If the opening of the spout is located 1.5 m above the grand, how far from be pout does water hit the floor? Ignore friction and dissipative forces.
A small statue is recovered in an archaeological dig. Its weight is measured to be 96 lb, and its volume 0.08 ft3. (a) What is the statue's weight density? (b) What substance is it?
(a) What is the mass of a deep breath of air having a volume of 2.00 L? (b) Discuss the effect taking such a breath has on your body's volume and density.
A large tanker truck can carry 20 tons (40.000 lb) of liquid (a) What volume of water can it carry? (b) What volume of gasoline can it carry?
What is the difference between flow rate and fluid velocity? How are they related?
A straightforward method of finding the density of an object is to measure its mass and then measure its volume by submerging it in a graduated cylinder. What is the density of a 240-g rock 89.0 cm3 of water? (Note that the accuracy and practical applications of this technique are more limited than a variety of others that are based on Archimedes' principle.)
Archimedes' principle can be used to calculate the density of a fluid as well as that of a solid. Suppose a chunk of iron with a mass of 390.0 g in air is found to have an apparent mass of 350.5 g when completely submerged in an unknown liquid. (a) What mass of fluid does the iron displace? (b) What is the volume of iron, using its density as given Table 14.1? (c) Calculate the fluid's density and identify it.
Verigy that the SI of hpg is N/m2.
Does atmospheric pressure add to the gas pressure in a rigid tank? In a toy balloon? When, in general, does atmospheric pressure not affect the total pressure in a fluid?
Suppose you are at the top of Mount Everest and you fill a water balloon. The air pressure at the top of Mount Everest is 58 kPa. a. What is the fractional change in the balloons volume V/Vi when you take it to sea level? b. If instead you take it 100 m below the surface of the ocean, what is the fractional change in its volume?