Water enters a fountain through a pipe with a cross-sectional area A₁ at a flowrate Q. The pressure in the inlet pipe is p₁. The water then leaves through a nozzle with a cross- sectional area A₂ and at an angle 0, as shown in Figure Q5. Both the inlet and the nozzle are at a height h₂, and the jet reaches a maximum height h3. I You may assume that viscosity is negligible. a) Find the horizontal force on the block b) What is the horizontal-component (u₂), vertical component (v₂) and magnitude (V₂) of the velocity of the jet as it leaves the nozzle?

Water enters a fountain through a pipe with a cross-sectional area A₁ at a flowrate Q. The pressure in the inlet pipe is p₁. The water then leaves through a nozzle with a cross- sectional area A₂ and at an angle 0, as shown in Figure Q5. Both the inlet and the nozzle are at a height h₂, and the jet reaches a maximum height h3. I You may assume that viscosity is negligible. a) Find the horizontal force on the block b) What is the horizontal-component (u₂), vertical component (v₂) and magnitude (V₂) of the velocity of the jet as it leaves the nozzle?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An incompressible fluid flows through a pipe without significant viscosity. It has a density of 124 kg per cubic meter. In a section of pipe with a 2.8 cm radius the fluid moves at a speed of 13 m/s, and has a pressure of 103,763 pascals. It flows into a section of pipe with a 3.87cm radius that is 5 meters higher than the first section. What the pressure in the second section of pascals?
m. A piston having a diameter 0.15 m and a length of 0.25 m as shown in figure (1.2) slides downward with a velocity (V) through a vertical pipe. The downward motion is resisted by an oil film between the piston and the pipe wall. The film thickness is 5*10° m, and the cylinder weighs 2.22 N. Estimate V if the oil viscosity is 0.016 N.s/m². Assume the velocity distribution in the gap is linear. 2. Figure (1.1) W D Figure (1.2) Scanned with CamScanner
The pipe flow in figure is driven by pressurized air in the tank. What gage pressure (P1) is needed to provide a water flow rate (60 m/h) take (v = 1.15*10 m2/sec).If the (P1 =700Kpa) and the fluid specific gravity is (0.68).estimate the viscosity of the fluid if the flow rate is ( 27 m/sec). 30 m Smoxoth pipe: d = 5 cn Open jet 80 m 10 m - 60 m 86
FLUID FLOW Example 5: A liquid food with a density of 800 kg/m³ is being transported at a rate of 5 ton/h through the system shown below. If the pressure at point 1 is 20 kPa gage, determine the pressure at point 2. Neglect friction losses. Example 5 P₁ = 20 kPa D₁ = 0.08 m 6 m 2 FLUID FLOW P₂ = ? D₂ = 0.025 m
A pipe is horizontal and carries oil that has a viscosity of 0.14 Pa s. The volume flow rate of the oil is 5.3 × 10^-5 m3/s. The length of the pipe is 38 m, and its radius is 0.57 cm. At the output end of the pipe the pressure is atmospheric pressure. What is the absolute pressure at the input end?
Question 4. The flowrate of the flow is 0,2 m³/s in a pipe placed on a horizontal plane. The pipe diameters are as 0.4 m and 0.2 m for D1 and D2, respectively. Find the 43 resultant force *(kN) acting to the pipe by the flow. The gauge pressure at (1) is P1=200 kN/m². (1) Figure 4
4. Water is flowing in a pipe with radius of 25.4 cm at velocity of 5 m/s. The viscosity of water is 1.131 Pa-s and its density is equal to 997.9 What is its Reynolds m³° number and type of fluid flow?
1. A fluid is flowing steadily through a vertical tube of length L and radius R. It has constant density and viscosity. Pressure at the tube entrance and exit are Po and PL .Take appropriate assumption and coordinate system and write the differential equations to solve the flow field. Also state the boundary conditions that are applicable here. Po P.
Water at 20 Degrees Celsius flows steadily with negligible viscous effects through the pipe shown. Both the pipe exit and top of the manometer are exposed to atmospheric pressure. The fluid in the vertical tube (manometer) is stationary so that the hydrostatic equation can be applied. Find: a) The gage pressure at point A (inlet of the pipe) b) The velocity at point A c) The diameter of the pipe outlet The density of water is 62.4 lbm/ft3 and 1 lbfs2/ft = 32.2 lbm.
VII. Suppose water is leaking from a tank through a circular hole of area A, at it's bottom. When water leaks through a hole, friction and contraction of the stream near the hole reduce the volume of the water leaving the tank per second to cAp 2gh where c(0
what will be the pressure gradient (kpa/m) at L=30 cm through the nozzle? At L=0, the liquid flows inside the nozzle has a specific gravity S=4.4, at L=0, the velocity is 2 m/s while at L=70 cm, the velocity is 6 m/s. Assume steady and inviscid flow. The velocity varies linearly with distance through the nozzle. 70 cm 6 m/s 2 m/s 60 cm Liquid
Q:- A solid circular cylinder of diameter 100 mm and length 200 mm slides inside a vertical smooth pipe that has inside diameter 100.5 mm. The small space between the cylinder and the pipe is lubricated with an oil film that has viscosity 3 N.s/m2.The cylinder weight 20 N and concentric with the pipe as it falls .Find the rate of the changer in velocity of the cylinder? Pbe Cylinder O Flm