Two cylinders act right after one another. Each cylinder is metered, and some actions are slow, and there is a dwell between some actions. What is the minimum flow rate required (CFM) to operate this cylinders? (enter answer with 2 decimal places) Sequence of operations: Cyl. A extends with metering (takes 1.5 second) Dwell time for 2 seconds for part machining Cyl. B extend and retracts without metering (2 second) Dwell time for 10 seconds while an electric mixer is operated Cyl. A retracts quicky with no metering (0.5 seconds) Dwell time for 5 seconds while a part is placed before next cycle Assuming the displacements of the cylinders are: Cyl. A DE = 65 in³ Cyl. A DR = 62 in³ Cyl. B DE 44 in³ Cyl. B DR = 41 in³

Two cylinders act right after one another. Each cylinder is metered, and some actions are slow, and there is a dwell between some actions. What is the minimum flow rate required (CFM) to operate this cylinders? (enter answer with 2 decimal places) Sequence of operations: Cyl. A extends with metering (takes 1.5 second) Dwell time for 2 seconds for part machining Cyl. B extend and retracts without metering (2 second) Dwell time for 10 seconds while an electric mixer is operated Cyl. A retracts quicky with no metering (0.5 seconds) Dwell time for 5 seconds while a part is placed before next cycle Assuming the displacements of the cylinders are: Cyl. A DE = 65 in³ Cyl. A DR = 62 in³ Cyl. B DE 44 in³ Cyl. B DR = 41 in³

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter8: Computer Numerical Control

Section8.3: Cnc Turning: Programming

Problem 7RQ: If a G1 code command is programmed partway through a machining operation, but no F-value is given in...

See similar textbooks

Similar questions

Two cylinders act right after one another. Each cylinder is metered, and some actions are slow, and there is a dwell between some actions. What is the minimum flow rate required (CFM) to operate this cylinders? (enter answer with 2 decimal places) Sequence of operations: Cyl. A extends with metering (takes 1.5 second) Dwell time for 2 seconds for part machining Cyl. B extend and retracts without metering (2 second) Dwell time for 10 seconds while an electric mixer is operated Cyl. A retracts quicky with no metering (0.5 seconds) Dwell time for 5 seconds while a part is placed before next cycle Assuming the displacements of the cylinders are: Cyl. A DE = 65 in3 Cyl. A DR = 62 in3 Cyl. B DE = 44 in3 Cyl. B DR = 41 in3
Briefly describe the use of I and J for the arc center method of circular interpolation.
While constructing a building, an engineer need to fix two steel beams together using a bracket as shown in Figure 1. Using absolute coordinate system, construct a G-code program for drilling hole number 2 only. To remove the metal chips the hole should be done in two equal steps. During the drilling, coolant should be on after spindle starts and stop before spindle stops. The spindle speed set to 1750 RPM. Drilling bit in rack number 2 and it should be 2 mm over the work piece. Drilling feed rate is 25 mm/min. Explain each code used in the program in a column. 57.5- 12.5 Hole (4) Hole (3) 30 10 Hole (2) Hole (1) X0 YO ZO 10 15 All dimensions shown are in mm Figure 1
Asap with define each of the following
CNC. Please write what each line of G- code means for each line. Thanks
Please show all the steps
Pls i need the counting of link and j1 and j2 with count on graph
In the FAPT programming language, the following format of statement Si= ................. is used to define: O Straight line Variable Branch commands Macro Point Circle O Cutting area
What is the easiest steps to draw this using AutoCad please? I need step by step answer please
SN=50 second time to askalways wrong answer please help
Write a CNC Milling program to machine the outer profile of a 6 mm thick aluminum sheet. Cutting parameters: depth of cut 3 mm, speed 1200 rpm, feed rate 100 mm/min, and coolant. Tool size 8 mm. (you can use the tool cutter compensations codes). Use an absolute coordinate from the point identified as tool position. 10 40 R 10 R 10 40 Tool position 20 z, 10 mm above All units in mm the sheet
im sorry for the inconvinience , 500 d/d means 500 rpm. Its translated from turkish textbook , i forgot to translate the rpm value. Could you correct the substitutions please ?