Two blocks are connected by an ideal spring on a frictionless floor as shown above. Force F is applied to the block with mass m2. If k is the spring constant, x=|L-Lol is the amount of the stretch/compression of the spring, and g is the free fall acceleration, what is a correct equation for the magnitude of the net force acting on block m2? Check all what applies.

Two blocks are connected by an ideal spring on a frictionless floor as shown above. Force F is applied to the block with mass m2. If k is the spring constant, x=|L-Lol is the amount of the stretch/compression of the spring, and g is the free fall acceleration, what is a correct equation for the magnitude of the net force acting on block m2? Check all what applies.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

F(t) Force_Crate Known values: Mass of Block 68 kg TT Hs μk 0 0.63 0.53 26° Problem Statement: A crate is initially at rest on a sloped surface, when a force is applied: F(t) where t is in seconds. Answers: When t=44.47 seconds, the crate has not yet started moving. Find the magnitude of the friction force at that time: 317.771 N The direction of the friction force at that time is: down the slope Find the time required for the crate to start moving: Find the crate's speed when t=174.9 s: 9.485 m/s Be sure to include units with your answers. 169.756 S 240+0.2 N,
Question 11: Figure 5 shows a lumped-parameter representation of a concept for a MEMS "tuning fork gyroscope" for measuring angular velocity. Displacements X₁, X2, and x3 are absolute positions of the respective masses and are measured from their static equilibrium positions where there is no deflection in the springs. The system friction is represented by three ideal lumped dashpot elements b₁,b2, and b3. Two external forces f₁ and f₂ are applied to masses m₁ and m₂, respectively. Derive the mathematical model of the MEMS gyroscope. x3 Leto, fi k₁ m3 k3 x1 m1 x2 m₂ f₂ b2
Kindly show the COMPLETE STEP-BY-STEP SOLUTION, DON’T DO SHORTCUTS OF SOLUTION, so I can understand the proccess. I will rate you with “LIKE/UPVOTE," if it is COMPLETE STEP-BY-STEP SOLUTION. If it is INCOMPLETE SOLUTION and there are SHORTCUTS OF SOLUTION, I will rate you with “DISLIKE/DOWNVOTE.” Topics we discussed: Statics of Rigid Bodies, Force System of a Force, Moment of a Force, Moment of a Force-Scalar Formulation, Moment of a Force-Vector Formulation, and Principle of Moment. Thank you for your help.
This most likely is made to be a probelm about mx''+bx'+kx=f(t) m = mass b = friction k = spring constant 4. A mass weighing four pounds stretches a spring 24 in. Suppose the mass is atequilibrium and is set into motion with a velocity of 6 inches per second. The mass is in a mediumwhere friction is small, and we assume it is zero. Note that the acceleration due to gravity near theearth’s surface where the experiment takes place can be taken as 32 ft/s2.(a) Suppose that in addition to the conditions described above, a hammer strikes the mass everyπ/2 seconds starting at t = 0. A delta function with impulse of 1 pound-second models theforce of each blow to the mass. Find the function x(t) for the displacement from equilibrium infeet of the mass at time t in seconds. Express x(t) as a piecewise defined function without the use ofunit step or Heaviside functions and such that in each time window it is a different multiple of the samesinusoidal function.(b) Now assume the same spring-mass…
Homework Q1/ A pulley is driven by a flat belt running at a speed of 600 m/min. The coefficient of friction between the pulley and the belt is 0.3 and the angle of lap is 160°. If the maximum tension in the belt is 700 N; find the power transmitted by a belt. [Ans. P= 3.974 kW]
480 ft-lbf First Gear (2.66) Final Drive (3.42) Axle Torque Thrust Force Figure 2 - Corvette Z06 and its transmission schematic. You start by measuring the 60-0 mph braking performance, which is accomplished along 30.56 m. The test weight (including the driver) was found to be 1510.5 kgf. 1) "Fuel is spent to make the vehicle go uphill, as you are aware. However, the fuel will not be restored if the vehicle is brought back from the hilltop to the initial elevation level."ANALYSE this statement under the laws of Thermodynamics.
k, k3 A В k2 What is the equivalent spring stiffness between the points A and B. If ki = 1 N/m, k2 =1 N/m. k3 = 2 N/m and k4 = 2 N/m A N/m
1. A weight of 8 lbf is attached to the end of a vertical spring which stretches 4 inches before reaching equilibrium. If the weight is pulled down 6 inches below equilibrium point and given an initial upward velocity of 8 ft/sec, find the equation of motion. Note: In solving for the spring constant k, make sure it ends up as a positive number.
1. Given: N Specific Weight = 25 m3 %3D • Mass = 2.2 Ibs m • Acceleration = 32.2 s2 Find: Diameter of Cylinder in inches • Remarks: Show your complete solution (with UOM) and conversion.
A) Find the acceleration constraint for this system. It is a single equation relating a1y , a2y and a3y . Hint: yA isn't a constant. Express your answer in terms of the variables a1y and a3y . B) Find an expression for the tension in string A. Hint: You should be able to write four second-law equations. These, plus the acceleration constraint, are five equations in five unknowns. Express your answer in terms of some, all, or none of the variables m1 , m2 , m3 , and constant g . C) Suppose: m1 = 2.5 kg , m2 = 1.5 kg , m3 = 4 kg . Find the acceleration of mass 1. Express your answer with the appropriate units. Enter positive value if the acceleration is upward and negative value if the acceleration is downward. D) Suppose: m1 = 2.5 kg , m2 = 1.5 kg , m3 = 4 kg . Find the acceleration of mass 2. Express your answer with the appropriate units. Enter positive value if the acceleration is upward and negative value if the acceleration is downward. E) Suppose:…
Bonus Question: 8 Extra points A block of mass m = 1.0 kg is dropped from height h= 75cm onto a spring. The mass will attache to the spring and then the spring will compress. a). Find the spring constant if the maximum distance the spring is compressed is 10cm in following arrangement? ០០០០០០០០០ b). Find the maximum distance the spring is compressed in following arrangement if the angle is 30 degrees? You are using same spring. ss. mmmm 8
Problem Solving: )An object falls from rest in a medium offering a resistonce. The velocity of the object hefore the ohject reaches the ground is given by the differential egua- tion dv/t + V% = 32, t/sec. uhat is the veloaty of the okject one second after it falls ?