Transistörün aktif bölgedeki çalışması için aşağıdakilerden hangisi ya da hangileri doğrudur 1. Kollektör akımı kolektör geriliminden bağımsızdır II. Kollektör akımı beyz akımına bağlıdır III. VCE gerilimi Vcc nin yarısı civarındadır Lütfen birini seçin: O a. I, II O b. Yalnız II c. Yalnız I Od. I, II, III II, III e.

Transistörün aktif bölgedeki çalışması için aşağıdakilerden hangisi ya da hangileri doğrudur 1. Kollektör akımı kolektör geriliminden bağımsızdır II. Kollektör akımı beyz akımına bağlıdır III. VCE gerilimi Vcc nin yarısı civarındadır Lütfen birini seçin: O a. I, II O b. Yalnız II c. Yalnız I Od. I, II, III II, III e.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Haritalar A (99+) Academia.ed... BUZEM Türkçe (tr) ▼ O Power Electronics_1 slerim / Çeşitli / MÜHENDİSLİK FAKÜLTESİ / Elektrik Elektronik Mühendisliği (İngilizce) / E2E350_Power Electronics 1/ 10 For controlled half wave rectifier, R=84ohm, f=50Hz and Vm=280V and a=1,5 rad. Calculate the power (W) absorbed by the load. Yanıt: In your calculations, take 3 digits after the comma and take pi = 3,14; Enter your answer into the system in terms of the desired unit only as a number.
Question 14 Transistors are examples of Select one: O a. O b. O C. O d. O e. ..electronics device. pyroelectric optical piezoelectric active passive
Ic 140uA 120UA 100uA IB RC RB ww B VCE 60UA VBB V BE Vcc 40uA OuA 10 12 14 Vce [V] Başka yönergeler almak için tıklayın Draw the load line and calculate the base current (IBO), collector current (Ico), the voltage between collector and emmiter pins (VCEO) and the power (Po) of the BJT transistor in the given circuit at the operating point. Technical characteristics of the transistor is given in graph. RB = 155k [2], Rc = 2k [Q], VCc = 12 [V], VBB = 10 [V], Vy=VBE = 0.7 [V]. IBQ IcQ = mA VCEQ= V PO= |mW Ic [mA]
ل توجد بطاقة D Test_5.docx → For the given circuits and input waveform determine the output waveform 22 kn 20 1. a) 15 b) C) d)
Ministry of Higher Education & Scientific Research. Subject: Basic Electronic Engineering. Year: First University of KUFA / College of Engineering. Time: 1 hour Date: 07 / 07 /2021 Electrical Engineering Department. Examiner: Dr. Heba Al-Asady ン (Mid exam _ 2021) Note: Answer all questions, all questions have the same marks. Q1\ Draw the bridge full wave rectifier and explain the operation of each part in the circuit. Q2\ For the circuit below, draw the output voltage vo. R 2 k2 8V 25 sin(ot) (1)"a 10 V Q3\ Explain in detail the effect of applying a voltage source on a pure semiconductor and dopped semiconductor. Explain with the help of drawing how these types are employed to conduct the charges. Q4\ For the circuit shown in figure below ,Given: VSS=3V, and R=2 k2. The diode that used in this circuit is made from silicon. Draw the I-V curve of the diode and find: the diode current and voltage at the operating point (Q-point). + Vss ip Dr. Heba Al-Asady
Identify the right statement relating to Zener impedance a. O b. O c. O d. the ratio of change of current to the change in input voltage in the breakdown region the ratio of change of voltage to the change in input power in the breakdown region None of the above the ratio of change of voltage to the change in input current in the breakdown region
OMANTEL Ilı. A moodle1.du.edu.om Question 6 Not yet answered Marked out of 3.00 P Flag question A buck converter produces an output voltage of 25 V across a 10 Ohm load resistor. The output voltage ripple is 0.5 %. The dc supply is 48 V. The switching frequency is 40 kHz. Assume continuous conduction. Calculate the value of the сарacitor. Select one: O a. 20 micro Farad O b. 25 micro Farad c. None of the above d. 30 micro Farad O e. 15 micro Farad Previous page Next page II
Give the meaning of each acronym of solid state devices. Also sketch the schematic symbol for each device. SUS Shockley diode D-MOSFET JFET SCR DIAC THYRISTOR Device TRIAC 1. 3. 4. 6. 8. 10. 12. 14. Symbol 2. 5. 7. 9. 11. 13. 15. Meaning No entry
Determine the following for the fixed- biased configuration. (Use 4 decimal places and show complete solution) a. IBQ and ICQ b. VCEQ c. VB , VC and VBC
What is the peak factor of 169sin 377t?Ans. 2.02
Explain the opera tion principles of Yotating tansformer with neat Sketch. Also, define the laws and oules fovolved in it.
Q Prove That the deivative How of :- is equal to defination of LC frequeney.