Three identically shaped segments of different materials have a voltage of 120 mV applied between their ends. As a result of the voltage, segment A has a current of 2500muA , segment B has a current of 105 μA and segment C has a current of 0.000002 A. The materials are conductor, semi- conductor and insulators as Determined?

Three identically shaped segments of different materials have a voltage of 120 mV applied between their ends. As a result of the voltage, segment A has a current of 2500muA , segment B has a current of 105 μA and segment C has a current of 0.000002 A. The materials are conductor, semi- conductor and insulators as Determined?

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter12: Electronic Control Devices

Section: Chapter Questions

Problem 14RQ

See similar textbooks

Similar questions

Figure Q1(a) shows a piece of ferromagnetic core with magnetic flux (B) with circular current (I) around the core. Figure Q1(b) show laminated ferromagnetic core with the same magnetic flux (B) and circular currents. With the aid of diagrams, explain how the current as highlighted in red (I) is developed in the ferromagnetic core in Figure Q1(a). B (a) (b) Figure 1(a) A ferromagnetic core and (b) laminated ferromagnetic core
Question 1 A ferromagnetic core with a relative permeability of 1500 is shown in Figure 2. The dimensions are as shown in the diagram, and the depth of the core is 7 cm. The air gaps on the left and right sides of the core are 0.070 and 0.020 cm, respectively. Because of fringing effects, the effective area of the air gaps is 5 percent larger than their physical size. If there are 400 turns in the coil wrapped around the center leg of the core and if the current in the coil is 1.0 A, what is a) the flux in each of the left, center, and right legs of the core? b) the flux density in each air gap? 7 cm ст ст 30 cm 30 cm 7 cm 400 turns 0.05 cm 30 cm 0.07 cm 7 cm Core depth = 7 cm Figure 2
Q3: Two circuits are arrange as shown in figure (1), (a and b) each one of them has two identical conductors , the vertical distance between each conductor in the same circuit is 1 m, the distance horizontlly between circuits is 30 cm, take 1 cm as diamter for each conductors. Derermine the inductance per km of the double circuit ? a a' b' FIGURE (1)
Question A suspension type insulator has three units with self-capacitance C and ground capacitance 0.1C. What will be the string efficiency?
Ferromagnetic materials have this characteristic. A. A relative permeability slightly less than one. B. A relative permeability slightly greater than one. C. A very high resistivity. D. A high relative permeability.
. Using the I – V curves how are ohmic materials different from non-ohmic materials
Figure Q1(a) shows a piece of ferromagnetic core with magnetic flux (B) with circular current (I) around the core. Figure Q1(b) show laminated ferromagnetic core with the same magnetic flux (B) and circular currents. With the aid of diagrams, explain what happens to the current in Figure Q1(a) if the magnetic flux is always constant. (a) (b) Figure 1(a) A ferromagnetic core and (b) laminated ferromagnetic core
25 PROBLEMS 12 cm +1.5-mm gap IP1000t Armature (sheet steel) Cast steel A = 2 cm? throughout FIGURE 1.27. The relay shown in Figure 1.27 has a core made of cast steel and an armature of sheet steel. A flux of 0.8 T in the air gap produces a force that pulls in the CO armature. a. Determine the required current to pull in the armature. b. What force is exerted on the armature to overcome the spring tension? c. Assuming in the closed position the air gap is reduced to 0.1 mm, to what value may the current be reduced (dropout current of relay) just to retain closure? Assume that the same force is required in the closed position to overcome the spring force.
The 'skin effecť is a phenomenon experienced when current flows through a metal. Which two of the following statements are correct? 15 Select one or more: O a. A smaller 'skin depth' implies a higher resistance O b. Direct current can cause the skin effect O c. The skin depth is smaller in highly conductive metals O d. The skin depth is larger in metals with high magnetic permeability
Problem A potentiometer is an instrument for measuring an unknown voltage in comparison to a standard voltage. In the potentiometer shown in Figure 1.0 a 16.0-m stretch of wire AB is connected to a 9.00-V battery. The resistance per unit length of the wire is 16.0 0/mm. The movable contact P is at point B. An ammeter (circle with A inside) is connected to point A. 16.0 m A B www Figure: 1.0 A V = 9.00 V
I changed the wire material from copper to aluminum to string refer to the figures below. Can you explain the difference of the three materials? There are overload that happened.
An over head string has 4 insulators. The voltage between the steel pin of the second insulator and metal cap of the fourth insulator is represent by *