The voltage across three component in a series circuit when connected across an AC supply arev1= 30 sin (300nt -") voltsv2 = 40 sin(300nt +voltsv3 = 50 sin(300rnt +voltsCalculate the a) supply voltage in sinusoidal form, b) the frequency of the supply, and the periodic timeand RMS value of the supply.

Brief description : Let us consider a sinusoidal signal V(t) = Vm sin(wt + Φ) Volt Vm : Peak Value…

The voltage across three component in a series circuit when connected across an AC supply are 30 sin (300nt – ") volts v2 = 40 sin(300nt + volts v3 = 50 sin(300nt +) volts Calculate the a) supply voltage in sinusoidal form, b) the frequency of the supply, and the periodic time and RMS value of the supply.

The voltage across three component in a series circuit when connected across an AC supply are 30 sin (300nt – ") volts v2 = 40 sin(300nt + volts v3 = 50 sin(300nt +) volts Calculate the a) supply voltage in sinusoidal form, b) the frequency of the supply, and the periodic time and RMS value of the supply.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Similar questions

Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor, and a 4 capacitor. (a) Draw the circuit diagram. (b) Compute the series impedance. (C) Determine the current I delivered by the source. Is the current lagging or leading the source voltage? What is the power factor of this circuit?
The ripple factor for pure dc is Answer:
Shown in the figure below is an "RL" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 9.84 Volts and is running at a frequency of f = 8.585e+04 Hz. The resistor has a resistance of R = 2170 and the inductor has an inductance of L = 3.54e-03 Henries. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Determine the numerical value of Ztot = 2890.5 Determine the numerical value of $z= = 41 Determine the current through the circuit: • I(PEAK) = 4.81E-3 • I(RMS) = 3.404E-3 Determine the voltage across the resistor: • VR(PEAK) = 7.387 • VR(RMS) = 5.22 ✔✔ Amps ✔Amps Write the FORMULA for the phase of the total impedance of the circuit z... = | tan-1 2701 R x Volts X Volts Determine the voltage across the inductor: • VL(PEAK) = 9.184 • VL(RMS) = 6.49 ✔ Volts Volts L R²+ WL- ✔ degrees 2 If a second circuit were connected in parallel with the inductor, this circuit would be considered as: O a low-pass filter O a capacitive switcher…
Shown in the figure below is an "RC" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 11.58 Volts and is running at a frequency of f = 1.326e+04 Hz. resistor has a resistance of R = 3750 2 and the capacitor has an capacitance of C = 3.17e-09 Farads. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Write the FORMULA for the phase of the total impedance of the circuit tot = Determine the numerical value of Ztot = Determine the numerical value of Pztot= Determine the current through the circuit: • I(PEAK) = • I(RMS) = Determine the voltage across the resistor: Amps Amps S2 C degrees
2. Refer to the Figure 2. a) Determine the total impedance of the circuit in polar form. b) Determine the voltage v(t) and current i(t) sinusoidal forms. Sketch one cycle of the waveforms in the same x-axis. Clearly indicating the peak value and the period of each waveform and the phase difference (in milliseconds) between the two waveforms. c) Determine the values of resistance R and inductance L. d) Determine the phasors V,, VR and Vc. e) Sketch the phasor diagram showing Vs, Vr, Vr, Vc and I.
An alternating current varying sinusoidally with a frequency of 50 Hz has anrms value of 20 A.a) Determine the instantaneous value at 0.0025 seconds.b) Determine the instantaneous value, 0.0125 seconds after passingthrough a positive maximum value.c) At what time, measured from a positive maximum value, will theinstantaneous current be 14.14 A?
Q18. An AC waveform is shown in figure B3. 4 10 20 30 40 50 70 100 Time (ms) 110 -2 -3 -4 -5 Figure B3 i) For the above waveform, determine a. Peak-to-peak voltage b. Time period c. Frequency ii) For the above waveform, determine a. Peak Factor b. Form Factor
Draw the sinusoidal waveform of the AC voltage and current for the given loads below. Describe the characteristics of the waveform for each load. A. Pure resistor B. Pure inductor C. Pure capacitor
In DC choppers the wave forms for input and output voltages are respectively a. both discontinuous b. discontinuous,continuous c. both continuous d. continuous,discontinuous
(b) An engineer is required to analyse a sinusoidal waveform for the voltage and current using oscilloscope. The voltage waveform produced Root Mean Square (RMS) value at 75 V with positive-going zero crossing at 30°. While the RMS value of current is 66.71 A with negative-going zero crossing at 0.349 rad. Assume the frequeney of both waveforms is 50 Hz. (i) Sketch the voltage and current waveform in the same axis by showing the important point. (ii) Determine instantaneous voltage when t = 8ms . (iii) Determine phase relationship between voltage and current waveform.
The single phase AC sinusoidal voltage then the rms value of the voltage v is .........
Ooredoo 876% D 9:31 Red Bull MOBILE Assignment EP se..6c205abd8b27a - Saved Q1. A square waveform with following specifications RMS Voltage 163.21 Time for two cycle 35ms Sketch the Square waveform. [1] Q2. A coil impedance of 680 is connected and the circuit has capacitance of 0.002mF is