The link lengths and the value of 2 and offset for some fourbar crank-slide linkages are defined in Table 1. The linkage configuration and terminology are shown in Figure 1. For the rows assigned, find (a) all possible solutions for angle 3 and slider position d by vector loop method. (b) the transmission angle corresponding to angle 03. (Hint: Treat the vector R4 as virtual rocker) Show your work in details: vector loop, vector equations, solution procedure. Table 1 Row a ن امان b Link 2 1.4 3 5 Link 3 4 8 20 Offset 1 2 -5 க 45° -30° 225°

The link lengths and the value of 2 and offset for some fourbar crank-slide linkages are defined in Table 1. The linkage configuration and terminology are shown in Figure 1. For the rows assigned, find (a) all possible solutions for angle 3 and slider position d by vector loop method. (b) the transmission angle corresponding to angle 03. (Hint: Treat the vector R4 as virtual rocker) Show your work in details: vector loop, vector equations, solution procedure. Table 1 Row a ن امان b Link 2 1.4 3 5 Link 3 4 8 20 Offset 1 2 -5 க 45° -30° 225°

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. Find a combination of link lengths where motion of a point on output link is one quarter of a circle. 2. Find the value of all 0, 0, 0, and y in open and close configuration Read the value of link lengths and the input angle 8., then use the formulae given below to calculate the value of unknowns 03, 0, and y K₁ = = K₂= d K2 K3 = a²-b²+c²+d² 2ac A = cos 0₂ - K₁ - K₂ cos 0₂ + K3 B = -2 sin 0₂ C = K₁ (K₂ + 1) cos 02 + K3 -B± √B²-4AC 2A 0412 = 2tan-1 d K₁ = — K5 = c²d²a²-6² 2ab D = cos 0₂ - K₁ - K4 cos 0₂ + K5 E = -2 sin 0₂ FK₁+ (K₁ - 1) cos 02 +K5 0312 2 tan-1 (-E± -E± √E²4DF 2D Y = 04-03
The figure below shows an offset slider crank linkage. The links lengths are: link2 = a= 100 mm and link3 = b = 600 mm. The offset is c = 190 mm. we need to : 1. determine the maximum horizontal position of the slider B (dmax) and the corresponding input angle 02 2. determine the minimum horizontal position of the slider B (dmin) and the corresponding input angle 02 Y 03 y В R3 R4 R, 04 R2 02 d ► X R1 The maximum horizontal position of the slider is dmax = Choose... + The input angle 02 corresponding to dmax , in degree and measured CCW from X axis, is = Choose... + The minimum horizontal position of the slider is dmin = Choose... + The input angle 02 corresponding to dmin , in degree and measured CcW from X axis, is = Choose.. +
4. A general fourbar linkage configuration and its notation are shown in the following figure and table. Find a 3, a 4,A¼, ABA, AB,Ap for open circuit by vector loop method. Row Link 1 Link 2 Link 3 Link 4 02 Rpa 63 6 2 7 9 30 10 6 30 - 12 - 15 7 3 8 85 25 3 10 6 8 45 -10 10 80 d 7 25 24 - 4 45 e 75 -50 10 300 Rp B A 03 2 X 04 NO O55
Position Analysis of the crank-slider linkage. The link length and offset for a fourbar slider-crank linkage are: link 2= 3.5, link3= 10, offset=1. Find both open and crossed solutions for angle theta3 and slider position, d, as driver makes a complete revolution.construct graphs to describe how the slider and theta3 varies as theta2 makes the entire revolution.
For the following 3-DOF RPR Industrial manipulator arm shown in figure: Joint 2 Joint 3 End point Pe Joint 1 Base Figure 1 3-DOF RPR (Industrial manipulator arm) Provide the step by step procedure for the frame assignment. a. Design and assign the labels for the given industrial manipulator arm b. Formulate the coordinate frames based on the D-H representation.
1. For the fourbar linkage shown (Fig. 1) [5]: 25 cm A 34 10 cm (crank) 02 3 20 cm 25 cm 25 cm P 04 FIGURE 1. Hoeken's linkage (a) Solve for 03 and 04 if the crank angle 02 = 120°. Show your work. (You may want to use the scripts to verify your answers.) (b) Find the position of point P when the crank angle is at 60 degrees.
Consider the 2-position design problem depicted below. The mechanism is GRCR. The linklengths and the positions of anchor points O1 and O2 are provided.a. Do any toggle positions exist between configurations CD and C’D’ that would prevent themechanism from completing the motion? If so, at what angle(s) of θ do they occur?b. Find new values for the coordinates (X,Y) of O2 that would enable the mechanism to bedriven by a driver dyad attached to link O1C, e.g., point B.c. What are the coordinates (X,Y) of O2 closest to the origin for which the mechanism canstill be driven by a driver dyad attached to link O1C, e.g., point B, as in part b?
Figure below shows a four-bar linkage (non-scaled diagram) at an instant. The input angle is equal to the output angle (02 - 04) and the transmission angle is 30°. The input link is extended beyond joint B and an input force (Fin) is applied at the end of it, while an output force is drawn from the midpoint of the output link. If an output force of 30 N is desired from an input force of 10 N, how far the input link should be extended, i.e., what is the distance from point B to the point where Fin is applied. Fin B out undefined 02 04 A. Non-scaled diagram; AB = 10, CD=r4 = 30 (output), all in mm
‏The linkage in Figure P7-5b has 04A = O2A = 0.75 , AB = 1.5 , and AC = 1.2 in . The effective crank angle in the position shown is 77º and angle BAC = 30 ° . Find a3 , AA , AB , Ac for the position shown for m2 = 15 rad / sec and a2 = 10 rad / sec2 in the directions shown using an analytical method . ( Hint : Create an effective linkage for the position shown and analyze it as a pin - jointed fourbar . ) the linkage has a parallelogram form Assume rolling contact C 02 A 3 . B 02 02 T
You are given a set of three links with lengths 2.4 in, 7.2 in, and 3.4 in. Select the length of a fourth link and assemble a linkage that can be driven by a continuous-rotation motor. Is your linkage a Grashof class I or nonGrashof class2 linkage? (Show your work.) Is it a crank-rocker, double- rocker, or double-crank linkage? Why?
Create a Kinematic Diagram of the following RLR or RPR robotic arm. Show coordinate, and link length and proper orientation following the Denavit-Hartenberg frame method. Place you into the above box.
Define and show on the figure the necessary vectors and their angles for second mechanism and construct the corresponding vector-loop equation(s). please draw the vectors and angles and visually show them on mechanism you can name the angles theta1, theta2 etc. it should be looking exactly like the example( first mechanism).