Study the image below. The bull's-eye represents the accepted true value. Eachcross represents a repeated measurement of the same quantity. Describe each ofthe figures by choosing its description inside the box.Precise and AccurateC. Notaccurate but preciseAaureta but nat nrnsinsNot a gsuretaFigure 1Figure 2Figure 3Figure 4I.What is your basis for your choices in describing the figures above?What is your idea about accuracy? How about precision?

This is the answer to question II Let us first understand what is meant by Accuracy and precision:In…

Answered: Study the image below. The bull's-eye…

Glencoe Physics: Principles and Problems, Student Edition

1st Edition

ISBN:9780078807213

Author:Paul W. Zitzewitz

Publisher:Paul W. Zitzewitz

Chapter1: A Physics Toolkit

Section1.1: Methods Of Science

Problem 4SSC

See similar textbooks

Similar questions

A cylindrical rod is 6.21 m long and has a diameter of 1.77 in. Calculate its volume, V, in cubic meters. Useful fact: 1 in. = 25.4 mm. If the volume is V = nx10m. enter the number n below. Do not give us the volume V. Give your answer correct to two decimnal places. n3D Typeyour answer.
Can you solve these problems and show steps w/ brief explanations? thannk you.
Please explain the answers in easy to understand way. What can you say about the accuracy of your measurements? What can you say about the precision of your measurements? Measure the longest dimension of the room twice, using two different techniques. Do the measurement in feet and inches. Then convert to meters. Below is what I got. Tape Measure - 146 inches > 3.7084 meters / 12 feet and 2 inches = 12.1667 feet > 3.70840 meters Ruler - 144.5 inches (144 + 1/2) = 3.6703 meters / 12.0416 feet = 3.67027 meters
A. Unit Conversion. Show your complete solution. Write your answers up to 3 significant figures. Recall: 1 Gy = 100 rad, 1 Sv = 100 rem 1. 3.5 μGy to mrad 2. 5.0 mrad/h to mGy/h 3. 45.0 mrem to μSv
Cube A is 2 inches on a side. Cube B is 8 inches on a side. Determine the following:1. The volume of each cube.2. How many Cube As can fit in Cube B (in regards to volume)?3. Noticing that B’s side is 4 times larger than A’s, can you see how you can get answer 2 any way other than finding both cube volumes?
Remember for these problems that in calculating the results, l'm using the value of nfound on the PRC. If you round 7 to 3.14 in your calculations there is potential for your answer to be taken out of toler- ance for a solution that uses the correct method. For numeric entry problems, report more digits in your answer than are significant, convert to standard units if necessary, and do not include the unit in the answer field. Bb understands 1.2345 E4 with no spaces and the E capitalized to be 1.2345 x 104 if you choose to enter numbers in scientific notation. Problems 1-3 refer to the following figure. In the above figure, the master cylinder has a circular cross section and a radius of 1.000 m. The slave cylinder has a radius of 24.50 cm. 1) What force must be applied down on the piston of the master cylinder to attain a pressure of 1.600 × 10° Pa in the system? A) 3.01 72x 105 N B) 3.01 74x 105 N C) 3.01 75 x 105 N D) 3.01 76x 10° N E) 5.02 40 × 106 F) 5.02 72 x 10° N G) 5.02 65 ×…
Please help me draw on cubic.!. and detail for explain.!. dont copy from previous answer! thanks!!!
Completely solve. Box the final answers. Use 3 decimals. Write legibly.
Already posted this question... still confused. The person who answered it before doesnt explain how or where they got the some figures from.
1. Is there a difference in the accuracy of measurements of the reading if the units used vary? Why? 2. Up to what precise measure could each instrument be read? 3. Which of these three measuring devices:ruler, verner caliper and micrometer is the most versatile? Justify your answer.
Please answer all parts. I cant answer with scientific notation so please do full value answers with correct sig figs
I have an homework where I was asked to get a generic 12 in/30 cm ruler and then answer the question in bold: Look at the smallest division and record what the uncertainty ▲x is of your tool. I am not sure how to ansswer this. Note: the previous question asked me to choose a unit of measurement on our tool which is the ruler and I choose inches (I hope that is a unit of measurement).

SEE MORE QUESTIONS

Recommended textbooks for you

Glencoe Physics: Principles and Problems, Student…

Physics

ISBN:

9780078807213

Author:

Paul W. Zitzewitz

Publisher:

Glencoe/McGraw-Hill

College Physics

Physics

ISBN:

9781938168000

Author:

Paul Peter Urone, Roger Hinrichs

Publisher:

OpenStax College

University Physics Volume 1

Physics

ISBN:

9781938168277

Author:

William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:

OpenStax - Rice University

Glencoe Physics: Principles and Problems, Student…

Physics

ISBN:

9780078807213

Author:

Paul W. Zitzewitz

Publisher:

Glencoe/McGraw-Hill

College Physics

Physics

ISBN:

9781938168000

Author:

Paul Peter Urone, Roger Hinrichs

Publisher:

OpenStax College

University Physics Volume 1

Physics

ISBN:

9781938168277

Author:

William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:

OpenStax - Rice University

SEE MORE TEXTBOOKS

Study the image below. The bull's-eye represents the accepted true value. Each cross represents a repeated measurement of the same quantity. Describe each o the figures by choosing its description inside the box.