estion 5 of 10AAnswers:or what value M of the clockwise couple will the horizontal component Ax of the pin reaction at A be zero? If a couple ofhat same magnitude M were applied in a counterclockwise direction, what would be the value of Ax?M= iPux3.0YIL--x*<190 lb3.0>BM1.8'56lb-ftlb1.8'MC0/10 E27°C T-s

Answered: Image /qna-images/answer/8fdef331-e387-455b-bc14-a806f798db8d.jpg

r what value M of the clockwise couple will the horizontal component Ax of the pin reaction at A be zero? If a couple of at same magnitude M were applied in a counterclockwise direction, what would be the value of Ax? A nswers: i i 3.0 + 3.0 190 lb I L --X B M 1.8' 56° lb-ft lb 1.8' 0/10 E C 27°C T-sm

r what value M of the clockwise couple will the horizontal component Ax of the pin reaction at A be zero? If a couple of at same magnitude M were applied in a counterclockwise direction, what would be the value of Ax? A nswers: i i 3.0 + 3.0 190 lb I L --X B M 1.8' 56° lb-ft lb 1.8' 0/10 E C 27°C T-sm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q7 Find the resultant of forces 680 N 300 500 mm A mm 660 N
Beam ABC is supporting beam CD. Which of the following gives the value of x if reaction at B is 380N Draw the FBD. THU X 600N 10m O x = 1.m O x = 1.50 m O x = 1.75 m O x = 2m O x = 2.50 m B WHIT +4 120N 1m 2m C 300N/m 12m D *
Q/ The built-up beam is formed by Welding together the thin plates of thickness 5mm. Determine the location of the shear center o. 1 200mm 200mm 300mm 100mm 100mm
SITUATION. The tower for a transmission line is modeled by the truss shown. The crossed members in the center section of the truss may be assumed to be capable of supporting tension only. Given: P=2.8kN 0=15⁰ a=3m b=3m c= 5m 5 panels@(a)m each F E b G B b b C a Q Zoom image Compute the force on member CL P
Determine the magnitude of the force which member CD exerts on the pin at C. A 36% B 0.49 m Answer: CD= i 0.40 m 245 N-m 0.40 m 136% D N /0.49 m
150 mm 60 mn 300 nm 000 m 50 mm 5 m B 25 kNm 5 m 10 KN A beam is created by nailing 3 planks together with 2 rows of nails as shown above. The beam exhibits a pin support at A and is suspended by a cable at B. A concentrated load of 10 kN is applied at the free end while a moment of 25 kNm is applied at location B. a) Determine the second moment of area (I) of the cross-section b) Draw the free body diagram, shear force diagram, and bending moment diagram of the beam c) For the maximum shear force on your SFD, determine the maximum and minimum shear stresses at the interface between the horizontal and vertical planks d) For the maximum shear force on your SFD, Determine the shear stress at the neutral axis
SITUATION. The tower for a transmission line is modeled by the truss shown. The crossed members in the center section of the truss may be assumed to be capable of supporting tension only. Given: P=2.8kN 8=15⁰ a = 3m b=3m c= 5m 5 panels@(a)m each D E b G P b b K C Zoom image Compute the force induced in member CD. C B
3. The length of 2-mm diameter steel wire CD has been adjusted so that with no load applied, a gap of 1.5 mm exists between the end B of the rigid beam ACB and a contact point E. If E = 200 GPa, determine where a 20 kg block should be placed on the beam in order to cause contact between B and E. D X 0.25 m 20 kg A 1.5 mm C 0.08 m 0.32 m E
SITUATION. The tower for a transmission line is modeled by the truss shown. The crossed members in the center section of the truss may be assumed to be capable of supporting tension only. Given: P=2.8kN 0=15⁰ a=3m b=3m c = 5m 5 panels@(a)m each F E b B b b P G C Zoom image Compute the force induced in member AB
Problem 2. Determine the horizontal and vertical components of the pin reaction at (B) on ABC for frame shown in the Figure. 10 N A B 1.5m C D 56 N.m 3m E- F G cord + F 1 1 1 2m 1.5m 2.5m 0.25m 3m
2. A four-link mechanism is known to have a force P = 0 kN on link 4. Calculate the torque on link 2 ? (Analytical and graphical solution) B 45 P 3. 4 T2= ? 45° 8 cm 02 04 .רgn 27 O2A = 10 cm; AB = 15 cm; 04B = 14 cm.
F, 70° 30 150 kN The parts are connected by pins at point O. Find the magnitudes of forces F1 and F2 that bring them into equilibrium by 0 at point O. O Find the magnitude of the force F1 and the angle a given that F2 = 80 N. : 60°. The parts are connected by pins in equilibrium, : 540 Fq %3D The ta