Q5) a) Calculate the minimum and the maximum input voltages that can be made by the given diode. The data sheet gives: Izmin = 2mA,Izmax=30mA, and Vz = 5V. b) In which region of I-V characteristic does the diode operate ? Why? c) What is the main function for the given circuit ? V1 -OV R1 100Ω 2 D1 1N5247B

Q5) a) Calculate the minimum and the maximum input voltages that can be made by the given diode. The data sheet gives: Izmin = 2mA,Izmax=30mA, and Vz = 5V. b) In which region of I-V characteristic does the diode operate ? Why? c) What is the main function for the given circuit ? V1 -OV R1 100Ω 2 D1 1N5247B

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

What is the difference between a diode and rectifier?
What is CEMF?
Select any diode from LTSpice Library. (The type of diode should either be RECTIFIER or SILICON) Create a Half-Wave Rectifier circuit. Use a resistor of 1000 Ohms. Input Voltage should be 95VAC - 65Hz Plot both the Input voltage and output voltage. Determine the Voltage drop across the diode by subtracting the output voltage to the input voltage peaks. Create a Bridge-Type Full Wave Rectifier Circuit. Repeat the steps done on the Half-Wave Rectifier circuit.
consider the figure below that shows an approximated reverse recovery turn-off characteristics for a power diode. Show that the following relation can express the total reverse recovery charge, Qrr = 1/2(trr*ts1) di1/dt =1/2(trr*ts21) di2/dt * ip Isl 1s2! -Ir
The reverse recovery time of diode is trr = 3 s and the rate off all of the diode current is di/dt = 30 A/s. The storage charge current QRR is?
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as germanium and D2 as silicon diodes. Input Vpp%3D20V, V1=3 V and V2=10 V. R D2 D1 Vin Vout V1 V2 Maximum voltage of output waveform Minimum voltage of output waveform Ps
Determine the state of diode for the circuit shown and find ID, VD. Assume simplified model for the diode. 4k02 2V 1k02. Off, 0.00mA, 0.4V O Off, -0.005mA, 0.0v On, 0.48mA, 0.6v On, 0.55mA, 0.7v Option 5
In the circuit shown below, find the diode voltage VD and the supply voltage V such that thecurrent is ID = 0.6mA. Assume the diode threshold voltage is 0.3 V. Determine the powerdissipated in the diode
Determine the value of RL that will establish maximum power conditions for the Zener diode.
A silicon diode has 1 ampere DC of current in biasd mode. What is voltage drop across the diode?
True or False. Please explain. thank you As the temperature increases, the forward voltage decreases in a silicon diode. Then, the graph of the forward bias region will shift to the left.
In the clamping circuit below, assume the diode has Von-0.7V and V₁ is a sinusoidal wave with a peak-to-peak amplitude of 10V. How much is the maximum value of the output voltage signal (Vmax)? And how much will it be if we set V₂=2V? Input V1 C1 0.1e-6 9.3 V and 7.3 V 9.3 V and 11.3 V 11.3 V and 7.3 V O 7.3 V and 12.0 V O 12.0 V and 7.3 V Output D1 1N4148 .tran 30-3 V2 0 Vmax V(output) 0.0ms putput MAN Input 0.6ms 1.2ms V(input) 1.8ms 2.4ms 3.0ms