Q2. All pn diodes shown below have a voltage drop of 0.3 V when they are "ON". +4V DIA ミ5k2 D2 VA VOUT 5k2 Ve DIB -2V Indicate in the table whether the diodes D1A, D1B and D2 are ON/OFF with the given VA and VB values. Also give the corresponding VOUT numerical values. CBA indicates the numbers 035 Ve DIA (ON/OFF) D8(ON/OFF) D2(ON/OFF) VoUT (sign and numerical value) VA OV A OV B A

Q2. All pn diodes shown below have a voltage drop of 0.3 V when they are "ON". +4V DIA ミ5k2 D2 VA VOUT 5k2 Ve DIB -2V Indicate in the table whether the diodes D1A, D1B and D2 are ON/OFF with the given VA and VB values. Also give the corresponding VOUT numerical values. CBA indicates the numbers 035 Ve DIA (ON/OFF) D8(ON/OFF) D2(ON/OFF) VoUT (sign and numerical value) VA OV A OV B A

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

What is the difference between a diode and rectifier?
In the circuit shown below. Determine the following a. Vs (at the secondary) b. Vout (across RL) c. Vrip (ripple votage) d. VDC e. PIV (Peak Inverse Voltage) 10:1 Output 115 V mis 60 Hz RL 2.2 k) D, 50μF- All diodes are IN4001. Tund AlMannai EENG261 Page 5/11
All pn diodes shown below have a voltage drop of 0.3 V when they are "ON". +4V DIA 5k2 D2 VOUT VA 5k2 V8 D1B -2V Indicate in the table whether the diodes D1A, D1B and D2 are ON/OFF with the given VA and VB values. Also give the corresponding VOUT numerical values. DIA (ON/OFF) DiB(ON/OFF) Dz(ON/OFF) VoUT (sign and numerical value) VA |V8 OV +4V OV +3V ov +4V
For the circuit shown in the Figure, if the diodes are silicon diodes with VD(on)=0.7 V, and VIn=50 sin wt V, V1 =7 V and V2 =13 V, then the value of VOUT (p-p) is: R1 D, D2 VIN VOUT vi E v2= Ca. 19.4 V Ob. 17.4 V Cc. 15.4 V Cd. 21.4 V
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to 220V ams 5OHZ İL-DC =05A RL VL-DC =20V
For the rectifier in the figure below, state the conduction sequence of the diodes for periods t1 to tó. D1 D2 D3 22) tl: D. & D.. 23) t2: D. & D.. 24) t3: D. & D.. 25) t4: D. & D.. D4 D5 D6 26) t5: D. &D. 27) t6: D.AN A & D....... Vm cot t6
For the following limiter consider that both zener diodes are identical with Vz = 4.5V @ lz =20mA and rz = 502. Also assume that the zener diodes will have a constant voltage drop of 0.75 V when forward-biased. R Z, Z a) Find the value of R such that the positive and negative limits are +5V when the input reaches ±10V. b) Sketch and label the voltage transfer characteristic for input voltages between ±10 V.
Consider the circuit with three diodes and a AC input, as shown below: D2 R1 D1 D3 R2 Assume that the input AC voltage is Ttsin(100TTT). You may consider the diodes to be ideal. mean voltage generated across resistor R2 is (assuming current direction to be from AC so into R1, through diode network, and through R2 from top to bottom): O a. 0.5V Ob. -0.5V O c. 1V O d. OV
consider the figure below that shows an approximated reverse recovery turn-off characteristics for a power diode. Show that the following relation can express the total reverse recovery charge, Qrr = 1/2(trr*ts1) di1/dt =1/2(trr*ts21) di2/dt * ip Isl 1s2! -Ir
Calculate the currents passing through the diodes D1 and D4 in the circuit given below. (All diodes are silicon).
The following circuit uses two Zener diodes with reverse breakdown voltage of 5.1 V for each. (1-a) Explain the operation of the Zener diode in forward and in reverse bias. (1-b) Analyze the circuit thoroughly assuming many source values that lead to all possible cases of diode states. For each case (Hint: 3 cases), re-plot the circuit and develop the relation between the output voltage and the source. (1-c) Draw input and output waveforms accurately over 0.5-ms period. Identify the diode states on the graph based on the categorization of cases from part (1-b). (1-d) Use Multisim to verify all of your results. Compare andcomment.
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as silicon and D2 as germanium diodes. Input Vpp=20V. V1=5 V and V2=9 V. R www D1 Vin Vout v1 V2 Maximum voltage of output waveform Minimum voltage of output waveform