Q2. A full-wave controlled rectifier circuit with resistive load shown below: Calculate the firing angle (as) if it is required to obtain an average output voltage of 70% of the maximum possible average output voltage. • Sketch the output Vg & ig waveform and determine the average current. 1:2 a, = 15 R= 302 Vs -v2x110 Sin 120rnt 2n ot VR

Q2. A full-wave controlled rectifier circuit with resistive load shown below: Calculate the firing angle (as) if it is required to obtain an average output voltage of 70% of the maximum possible average output voltage. • Sketch the output Vg & ig waveform and determine the average current. 1:2 a, = 15 R= 302 Vs -v2x110 Sin 120rnt 2n ot VR

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as germanium and D2 as silicon diodes. Input Vpp%3D20V, V1=3 V and V2=10 V. R D2 D1 Vin Vout V1 V2 Maximum voltage of output waveform Minimum voltage of output waveform Ps
3 Given the bridge-type full-wave rectifier circuit shown 220V 60Hz 220V:Es Es D1 D2 D3 D4 The load resistor is 220 and the transformer average current is 300mA. Determine: (a) Average value, RMS value, and frequency of load voltage VRL. (b) Average current and PIV of each diode. RL
H.W:- For a single phase half wave uncontrolled rectifier if the input supply voltage is (v= 310 sin314t), at frequency (f= 50 Hz). Then determine the followings:- Vm. Vmean- i. Draw the rectifier circuit. un %3D ii. Draw the input and the output voltages waveforms. iii. Determine the mean and rms values of the output voltage. s Ec iv. If the load is (R=10 S), then determine the mean and rms values of the current. 2019
Can someone please provide a step by step solution? Thank you! The full wave rectifier in the circuit below is to deliver 0.25A and 15V (peak) to a load. The ripple is to be no larger than 0.4 V peak-to-peak. The input signal is 120 V (rms) at 60 Hz. Assume V(lambda) = 0.7 V . Determine the required turns ratio, the filter capacitance, and the diode PIV rating.
S-2) a) On the bridge type full wave rectifier circuit given in the figure Plot the current paths for each of the +/- alternans. b) The waveform of the Vç output voltage is given in the graphs on the side. Draw it in the blank and calculate the peak value and indicate it in the graph. c) Calculate the effective value of the output voltage. (Vç (eff) =… ..?). Note: Diodes are not ideal. VD = 0.7V.
Draw the changes in Vi and Id of the ideal diode half-wave rectifier circuit in the figure. The frequency of the sine signal here will be taken as 50Hz. (Changes in Vi and Id will be drawn!!!)
Be a single-phase half-wave rectifier with an RL load. The sinusoidal input voltage has a frequency of 60 Hz and the value of R = 10 ohms. What is the value of L for the current extinction angle to be 270°. Tip: use Puschlowski's abacus.
Determine the output voltage of a Half-wave rectifier with an input peak-to-peak sinusoidal voltage of Vm.
What will be the out put of the D'Arsonval meters, if an average responding a.c meter of half-wave rectifier read (236 v), and true form foctor of input waveform is (114). *
Q1/ a/Draw the output voltage waveform for the bridge rectifier in this figure : 5:1 D Da 120 V ms Dy RL B/ What PIV rating is required for the diodes in a bridge rectifier that produces an average output voltage of 50 V? Q2/ Determine the minimum input voltage required for regulation to be established in the figure. Assume an ideal zener diode with Izx = 1.5 mA and V, = 14 V. lllee 幸

The PIV for each diode in a full-wave center- tapped rectifier is............. Note: Vp(out) = peak output voltage. Choose correct answer : A) Vp(out) + 0.7 V B) Vp(out) – 0.7 V C) 2Vp(out) + 0.7 V D) 2Vp(out) – 0.7 V