Q-An RC square column of size 600 mm is constructed to carry an unfactored load of 3000 kN. The ends of the column are restrained from displacement but free to rotate and is casted with M-25 concrete. The area of Fe-415 steel required to carry the given load considering that the column is short and loaded with minimum eccentricity is

Q-An RC square column of size 600 mm is constructed to carry an unfactored load of 3000 kN. The ends of the column are restrained from displacement but free to rotate and is casted with M-25 concrete. The area of Fe-415 steel required to carry the given load considering that the column is short and loaded with minimum eccentricity is

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter4: Compression Members

Section: Chapter Questions

Problem 4.7.10P

See similar textbooks

Similar questions

The light rigid bar ABCD shown is pinned at C and connected to two vertical rods. The bar was initially horizontal, and the rods were stress-free before the load P= 20 KN is applied. Sleel E-200 GPa A-400mm L1 m 2.0 m 0.6 m 1.5m P-20 KN Aluminum E70 GPa A-900mm L-1.5 m 1. Axial load at steel rod in kN? 2. Axial stress at steel rod in MPa? 3. Axial deformation of aluminum rod in mm? 4. Axial deformation of steel rod in mm? 5. Axial Load at aluminum rod in kN?
Auniform bar 1 is connected to a tapered rod 2. Both are subjected to axial loads as shown. If P- 7 KN, Determine the axial deformation of uniforn bar 1 (in mmi. Indicate negative sign if compression. 5P O 3P E-200 GPa gomm o mm Z so mm 30 mm 30 mn 30 mm 80 mm
Two circular shafts are joined together between fixed supports to resist a torsional moment of 80 kN-m as shown. Determine the absolute value of the maximum torsional shear stress of the hollow steel shaft (in MPa). 20 IN-m Sm stcel hellw circalar duminum Selid circular D= 75 mny Do- IDO mn D> 80 mm G- D GPon 6- IS0 EPa
954. The 2014-T6 aluminum rod AC is reinforced with the firmly bonded A992 steel tube BC. When no laad is applied to the assembly, the gap between end C and the rigid support is 0.5 mm. Determine the support reactions when the axial force of 400 kN is applied. 400 mm 400 kN A992 steel So mm S00 mm 25 mi2014-T6 aluminum alloy Section a-a
The 2014-T6 aluminum rod AC is reinforced with the firmly bonded A992 steel tube BC. When no load is applied to the assembly, the gap between end C and the rigid support is 0.5 mm. Determine the support reactions when the axial force of 400 kN is applied. 400 mm 400 kN B A992 steel 50 mm 800 mm 25 mm 2014-T6 aluminum alloy Section a-a -400(10*) N st (a)
The light rigid bar ABCD shown is pinned at C and connected to two vertical rods. The bar was initially horizontal, and the rods were stress-free before the load P 20 KN is applied. Sheel E200 GPa L-1 m 2.0 m 0.6m 1.5m P-20 KN Aluminum E-70 GPa A=900mm L-1.5 m What is the axial load at steel rod in KN?
Determine the principal stresses. Show all results on complete sketches of differential elements. (input the Maximum Principal Stress in the answer box) ox- 65 ksi, ay - 89 ksi, Dxy - 58 ksi
A uniform bar 1 is connected to a tapered rod 2. Both are subjected to axial loads as shown. If P- 7 kN, Determine the total axial deformation (in mm). Indicate negative sign if compression. 3P E-200 GP 3M 80mm 30 mm 30 mm 30 mn 30 mm 80 mm
The light rigid bar ABCD shown is pinned at C and connected to two vertical rods. The bar was initially horizontal, and the rods were stress-free before the load P = 20 KN is applied. Steel E200 Gra A-600mm L-I m 2.0 m 0.6m 1.5 m D. V P-20 KN Aluminum E-70 GPa A-900mm L-1.5 m What is the axial load at aluminum rod in KN?
How much service live load, in kN/m, can be supported? The member weight is the only dead load. The axial compressive load consists of a service dead load of 45 kN and a service live load of 90 kN. Do not consider moment amplification. Use NSCP 2015. a. b. LRFD. ASD. wt A kN/m mm² W460x144 1.41 18400 472 13.6 283 SECTION tw bf tf Ix Sx mm mm mm mm³ 22.2 726 3080 mm mm mm 199 6.2m W460x144 Sy Ty Zx ly mm mm³ mm 83.6 591 Zy J Cw mmº mm³ mm³ 67.4 3450 906 2440 4230 mmª
Principle of superposition The beam is indeterminate to the first degree. Force in member BD is chosen as the redundant. This member is therefore sectioned to eliminate its capacity to sustain a force. 60 kN/m 3 m 1.8 m 60 45 actual structure (a) 160 kN/m B FaD redundant рrimary structure ARD FRp applied Fap D
Q1/ The 15-mm diameter steel bolt is screwed tightly into a block at A. Suppose that the couple forces F causes the ends of the wrench to be displaced 3 mm, determine the maximum shear stress in the bolt. Assume that the wrench is rigid and modulus of rigidity of steel is 75 GPa. 150 mm i50 mm mni