Problem #1. The base of a rectangular reinforced concrete beam is 300mm and the effective depth is 550mm. Concrete compressive strength on the 28" day is 24MPA and steel yield strength is 415MP.. Determine : a. The depth of compression block (in mm, 2 decimal places), the strain in the tension steel (5 decimal places) and ultimate moment capacity (in KN.m, nearest tenth) of the beam if it is reinforced with 4-32mm diameter bars. b. The depth of compression block, the strain in the tension steel and ultimate moment capacity of the beam if it is reinforced with 4-20mm diameter bars.

Problem #1. The base of a rectangular reinforced concrete beam is 300mm and the effective depth is 550mm. Concrete compressive strength on the 28" day is 24MPA and steel yield strength is 415MP.. Determine : a. The depth of compression block (in mm, 2 decimal places), the strain in the tension steel (5 decimal places) and ultimate moment capacity (in KN.m, nearest tenth) of the beam if it is reinforced with 4-32mm diameter bars. b. The depth of compression block, the strain in the tension steel and ultimate moment capacity of the beam if it is reinforced with 4-20mm diameter bars.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A singly reinforced rectangular concrete beam has a width of 150 mm and an effective depth of 330 mm. The characteristic compressive strength of concrete is 20 MPa and the tensile strength of steel is 415 MPa. Adopt the stress block for concrete as per IS 456-2000 and take the limiting value of depth of neutral axis as 0.48 times the effective depth of the beam for considering as a balanced section. What is the likely approximation for the limiting value of the moment of resistance of the beam?
The properties of the reinforced concrete T-beam are bi = 30 in., hi = 4 in., b2 = 12 in., h = 18 in., Ast = 4.5 in?, and n=8. Using elastic analysis, find the maximum stress in the concrete produced by an 80-kip-ft bending moment. h1 h2 A« (total area) 10,606.391 psi O 343.813 psi O 543.318 psi 687.954 psi
The concrete post is reinforced axially with four symmetrically placed steel bars, each of cross-sectional area 900 mm2. Compute the stress in each material when the 1000-kN axial load is applied. The moduli of elasticity are 200 GPa for steel and 14 GPa for concrete. Compatibiltiy Equation . Ust Bearing |1000 kN plate Steel- Concrete 300 mm 300 mm Section a-a
21. The column of reinforced concrete is loaded with P = 8000 lbs. The modulus of elasticity (E) is 4.2E6 psi and the Poisson ratio is 0.15. 16in 16in What is the normal stress along section b-b? a. -15.625 psi b. -7.81 psi c. -2.60 psi d. -11.04 psi
3.) A reinforced concrete beam 300 mm width has an effective depth of 450 mm. it is reinforced with 6-32mmØ at the tension side and 2-28 mmØ at the compression side located at 65 mm from the top. f= 34.5 MPa and fy 345 MPa. Assume all steel yield and the contribution of compression steel may not be neglected. (NSCP 2001) a. Find the balanced steel ratio in percent? = b. Find the depth of compression stress block. c. Find the nominal moment capacity of the beam.
The concrete post is reinforced axially with four symmetrically placed steel bars, each of cross-sectional area 900 mm2. Compute the stress in each material when the 1000-kN axial load is applied. The moduli of elasticity are 200 GPa for steel and 14 GPa for concrete. Compatibiltiy Equation (20 points), o co (20 points), Ost (20 points). |1000 kN Bearing plate 1 a Steel Concrete 300 mm 300 mm Section a-a
In all Questions use the Working Stress Method and the flowing material 25 MPa and f, = 420 MPa. properties f = If the stress in the top fiber of the concrete is f = 12.5MPa and in the steel is 400 MPa. Ec 25000 MPa, Es 200000 MPa. Determine the following: 1-Maximum strain in concrete 2- Maximum strain in steel and 3- Flexural strength of the section (the moment M) P 500 mm 300 mm
A rectangular concrete beam has a width of 400 mm and an effective depth of 700 mm. It is reinforced with five 28-mm diameter bars for tension only. Concrete strength is f's = 21 MPa and steel yield strength is fy = 275 MPa. Which of the following most nearly gives the distance of the neutral axis from the extreme compression concrete? A. 139.51 mm B. 151.93 mm C. 118.58 mm D. 188.15 mm
2.From the figure below; bending moment of 8 KN-m. The normal weight of concrete has an fc' of 26.4 MPa. solve and show the complete solution and pick the correct ans
The total compressive force at the time of failure of a concrete beam section of width 'b' without considering the partial safety factor of the material is (a) 0.36 fok b Xu (c) 0.66 fok b Xu (b) 0.54 f b Xu (d) 0.8 f b X, ck where X, is the depth of neutral axis, f cube strength of concrete. ck
1) A rectangular reinforced concrete beam with dimensions b = 14 in, d = 25 in, and h = 28 in is reinforced with three No. 10 bars. Material strengths are fy = 60000 psi and fc' = 5000 psi. a. Find the cracking moment based on the uncracked transformed section b. Determine the maximum moment that can be carried without stressing the concrete beyond 0.45fc' or the steel beyond 0.6fy. Hint: Assume maximum compressive stress in the concrete to be 0.45fc' and check whether the maximum steel stress reaches 0.6fy. This way you can check which one is reached first C. Find the nominal moment capacity of the beam
Determine the required tension steel area of the T beam with given properties below. Width of flange bf = 500 mm Width of web bw = 340 mm Thickness of flange tf = 140 mm Effective depth d = 350mm Effective concretee covering d' = 75mm Compressive strength of concrete fc' = 34.5 MPa Yield stress of steel bar fy = 375 MPa Mu = 415 kN-m As = _________ mm2