pipeline between point A and B consists of 1000 ft of 18in followed by 800 ft of 12in followed in turn by 500 ft of 8 in. If f1 = f2 = f3 = 0.024 and the discharge is 2cfs. Calculate the following : The velocity of water in each pipe The head loss in each pipe The total head loss The discharge in term of gallon per minute

pipeline between point A and B consists of 1000 ft of 18in followed by 800 ft of 12in followed in turn by 500 ft of 8 in. If f1 = f2 = f3 = 0.024 and the discharge is 2cfs. Calculate the following : The velocity of water in each pipe The head loss in each pipe The total head loss The discharge in term of gallon per minute

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

PROBLEM 3 The properties of three pipes connected in series are tabulated below. (a) What is the head loss (ft) in each pipe for a total head loss in the system equal to 30 ft? (b) What is the flow rate (cfs)? pipe L (ft) d (in) f 1200 8 0.015 2 1000 6 0.015 3 2000 10 0.015
The properties of three pipes connected in series are tabulated below. (a) What is the head loss (ft) in each pipe for a total head loss in the system equal to 30 ft? (b) What is the flow rate (cfs)? pipe L (ft) d (in) f 1 1200 8 0.015 2 1000 6 0.015 3 2000 10 0.015
Two reservoirs are connected by two pipes of the same length laid in parallel. The diameters of the pipes are 100 mm and 300 mm respectively. If the discharge through 100 mm diameter pipe is 0·01 m3 /s, what will be the discharge [ in m3/s] through 300 mm pipe? Assume that f is same for both pipes. a. 0.504 b. 0.181 c. 0.156 d. 0.952
... L = 700m 2 4 D = 45cm L = 800m D = 40cm L = 600m L = 700m D = 35cm D = 35cm 1 A L = 700m В D = 40cm L = 1200m D = 40cm Water is flowing from point A to point B in the system shown in the figure. All the corresponding length and diameter of each pipe is shown. Assuming that each pipe has n=0.011 and head loss from point A to B is 30m, determine the a) discharge at pipe 1 b) discharge at pipe 3 c) discharge at pipe 5 A Q3 = 0.160 cu.m/s B) Q1 = 0.253 cu.m/s 3.
A discharge of 600 liters/sec flows through a pipe having a diameter of 400 mm., length of 40 m. long. Compute the head loss of the pipeline using Mannings Equation with n = 0.013. Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: m Decimal Places required in the final answer: 3
A pipe system has a flow of 4.6 cfs. Section 1 has a diameter of 12” and Section 2 has a diameter of 10”. What is the velocity at each section?
A B PROBLEMS 10.93, 10.94 10.94 Pipes 1 and 2 are the same kind (cast-iron pipe), but pipe 2 is four times as long as pipe 1. They are the same diameter (1 ft). If the discharge of water in pipe 2 is 1 cfs, then what will be the discharge in pipe 1? Assume the same value of ƒ in both pipes.
Moving to another question will save this response. Question 47 A pipe has a length of 462 m., and a diameter of 0.44 m. The coefficient of rougness is C = 128, and the headloss is 12 m. Determine the discharge (L/s) inside the pipe, Round off to three decimal places. A Moving to another question will save this response. «>
The total flow in the pipe system in the figure is 0.86 m³/s. Assume f = 0.032 for all pipes. A. What is the flow in pipeline 1? (m³/s) B. What is the flow in pipeline 2? (m³/s) C. What is the flow in pipeline 3? (m³/s)
1. Gasoline (sp. gr. 0.8) is flowing upwards a D, 150 mm vertical pipeline which tapers from 300 mm to 150 mm diameter. A gasoline mercury Outlet differential manometer is connected between 300 mm and 150 mm pipe section to measure the rate of flow. The distance between the manometer tappings is 1 metre and gauge reading is 500 mm of mercury. Find: 1) Differential gauge reading in terms of gasoline head; Gasoline (Sp. gr. = 0.8) 2) Rate of flow. Neglect friction and other losses between tappings. Inlet D, 300 mm 1 m
QUESTION 5 Q2. Two water pipelines converge into one line of 2.5m diameter. a). What is the velocity of water flowing in the converged line if the discharges and diameters of the converging lines are 1 m3/s with an 800mm pipe and 0.5 m³/s with a 500mm pipe? (m/s) b). What is the mass flowrate under these conditions? (kg/s) c). What percentage change in velocity would there be in the converged pipe if the diameter of the pipe was reduced by 20%? Take the density of water to be 103 kg/m3. Part a). is denoted Q5, part b). as Q6 and part c). as Q7
For the system of pipes shown in the figure below, the direction of flow is from 1 to 2. Which of the following is INCORRECT? Neglect minor losses. 1 Pipe A O a. hL1to2 = hƒA + hfB O b. hfc = hfD O c. O d. QB = QA Q₁ = QB + Qc + QD Pipe C Pump Pipe D P Pipe B 2