One side of a transformer has 1,800 turns while the other side has 450 turns. The high voltage side is connected to a 240 Vrms source. The low voltage side (secondary) is connected to an impedance ZL = 20 +j10 Q. For all questions requiring numerical answers, provide at least 2 digits after the decimal point. What is the voltage (in V rms) at the secondary? Answer: What is the current (in A rms) at the secondary? Answer: What is the current (in A rms) out of the source? Answer:

One side of a transformer has 1,800 turns while the other side has 450 turns. The high voltage side is connected to a 240 Vrms source. The low voltage side (secondary) is connected to an impedance ZL = 20 +j10 Q. For all questions requiring numerical answers, provide at least 2 digits after the decimal point. What is the voltage (in V rms) at the secondary? Answer: What is the current (in A rms) at the secondary? Answer: What is the current (in A rms) out of the source? Answer:

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.61P

See similar textbooks

Similar questions

A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and L=40mH. (a) Determine the power factor of the circuit and state whether it is lagging or leading. (b) Determine the real and reactive power absorbed by the load. (c) Calculate the peak magnetic energy Wint stored in the inductor by using the expression Wint=L(Irms)2 and check whether the reactive power Q=Wint is satisfied. (Note: The instantaneous magnetic energy storage fluctuates between zero and the peak energy. This energy must be sent twice each cycle to the load from the source by means of reactive power flows.)
One side of a transformer has What is the voltage (in V rms) at the secondary? 1,800 turns while the other side has 450 turns. The high voltage side is connected to a 240 Vrms source. The low What is the current (in A rms) at the secondary? What is the current (in A rms) out of the source? What is the value of the load impedance when referred to the primary? • Referred impedance = voltage side (secondary) is connected to an impedance ZL = 20 + j10 Q. Provide at least 4 digits after the decimal point. +j_ N What is the value of the source voltage (in V rms) when referred to the secondary?
A utility company plans to connect a total of 20uF of capacitance to a 7200 volt line. To make this connection four capacitors will be connected in series. What is the capacitance of each capacitor? Answer is 80uF. Now what is the minimum AC voltage rating of each capacitor?
Please show you detailed solution Number 10 A voltage of 250 volts at 50 Hz is impressed on a circuit having a 60-ohm resistor, 35-?F capacitor, and a 0.25-henry inductor in series. Determine power factor. A. 0.979 C. 0.924 B. 0.862 D. 0.707
(c)[ device needs to connect to a Diesel generator which generates sinusoidal AC power at 16.67 Hz. The amplitude or RMS value of the generator output voltage is adjustable. The area of cross-section of the core is 0.035 m². What constraints, if any, must be imposed on the The magnetic device of the figure is designed to operate with 240 V(rms) at 50HZ. For operation in a remote mining site, the use of this device, or the generator, if the device must be connected to the generator. You may assume that the peak B field in the core must be limited to 1.1 T to prevent magnetic saturation.
Consider a transformer with a primary coil consisting of 1490 turns and a secondary coil of 1900 turns. An alternating RMS voltage 232.5 V is applied to the primary coil, and the output RMS voltage 48 V is measured across the load resistor of resistance 114.5 Ohm connected to the secondary coil. What is the internal resistance of the secondary coil?
1) Calculate the maximum RMS current in p.u. that guarantees the equality of losses between the deformed and non-deformed regime for a power transformer equal to 400 kVA with Pcp = 6% in two cases: a) the transformer feeds a twelve-phase converter Idc=40 A b) the transformer feeds a six-phase converter Idc=40 A.
QUESTION 11 An inductor is connected in parallel with a 6540 resistor and a function generator. The applied voltage is 42V RMS and the total current is 67mA RMS. Find the magnitude of the current through the inductor. Enter your answer in the space provided. Round your answer to one decimal place. Your answer should be in mA but do not enter the unit.
In a transformer that has 10 times more turns on the secondary side (side 2) than on the primary side (side 1), the magnitude of the voltage/EMF across the windings on the secondary side, E₂ will be... O a.... 10 times lower than the voltage/emf on the primary side, E₁. O b.... the same as the voltage/emf on the primary side. O c.... always zero regardless of the voltage on the primary side, E₁. O d.... 10 times higher than the voltage/emf on the primary side, E₁.
A parallel connection of a RL branch with a C branch is connected across a 100V AC mains. At first R = 10 ohms, L = 20mH and frequency of 1000rad / s, the current measured is 2.2361A at 89.44 leading power factor. A) Determine the initial capacitance. B) However, a fault occurs on the capacitor branch making its capacitance 20% lower and a resistance of 5 ohms is detected. If this faulty circuit is rerun but at a frequency of 500 rad / s, determine the new current that will flow through the circuit.
The step down DC chopper uses DC source voltage V(dc) = 200 V and resistive load impedance of 10 ohm. The duty cycle is 0.4 the voltage drop across the switch may be taken as zero, Calculate : (a) Average and RMS value of output voltage. (b) Average and RMS value of output current.
A single-phase AC voltage controller has a resistive load R = 10 Ohm, and the RMS input voltage is Vs = 230 V, 60 Hz. The delay angle is 120 degree. Then power factor of the circuit is: Select one: O a. 1 O b. 0.75 O c. 0.44 O d. None of the above O e. 0.9