NAnsver all the questions (1) The rms value of the input voltage for a bridge network is shown in the following figure. (a) Sketch V, and determine average output V, for the configuration of the following figure. (b) Determine the de voltage and r.m.s voltage of output. (c) Determine the required PIV rating of each diode. (d) Does this network work as a clipper? Ideal diodes 170 V 2.2 ka 2.2 ka -170 V 2.2 ka

NAnsver all the questions (1) The rms value of the input voltage for a bridge network is shown in the following figure. (a) Sketch V, and determine average output V, for the configuration of the following figure. (b) Determine the de voltage and r.m.s voltage of output. (c) Determine the required PIV rating of each diode. (d) Does this network work as a clipper? Ideal diodes 170 V 2.2 ka 2.2 ka -170 V 2.2 ka

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

Consider the following circuit diagram. Using practical diode model solve the following items. i. What is the type of rectification in this circuit? ii. Calculate the total peak secondary voltage (Note that “RMS" value is given in the circuit) iii. Sketch the plot of time vs voltage over Load (RL) iv. Find the average voltage over Load. v. Find the maximum current passing over diodes. vi. Find the peak inverse voltage (PIV) over the diodes. vii. Find the minimum fuse current rating for the primary coil. 5:1 D DA 120 V rms D3 D2 RL=10kQ RL out ell lelll
In the circuit shown in the figure, diode voltages are given as 0.6V and rD = 100 ohms. When point B is open circuit AIf + 5V is applied to the point of application, drawing the shape of the circuit formed and calculating the currents passing through the resistors.calculate.
A 6.3V AC signal is half-wave rectified and applied to a 33-ohm load resistance. Determine the peak load voltage, the average load voltage, and the average current.Determine also what diode would be optimized to use in this circuit.
There are three diode models namely (i) the exponential, (ii) ideal and (iii) the constant voltage source. a) Please define each model and provide the factors that influence the choice of a diode model when analyzing a circuit ? b) Please provide sketches of the I-V characteristic of each model.
Build the diode clamping circuit given in the figure. Voltage waveforms vS and vO draw
Determine current through each diode in the circuit .Use Practical Diode model. Assume diodes to be similar.
Draw the characteristic curve of the standard PN-coupled semiconductor diode.Specify the correct and reverse polarity zones on the curve and draw the appropriate connection shapes.After mark the critical points on this curve and explain what these points mean.
b. Calculate the following about the circuit in the figure (If silicon diodes are employed in the rectification);i. the peak value of the output voltage considering the drop across each diode, Vpk.ii. the average voltage, Vdc. iii. The current through the load resistor, IL.iv. The current diode, Id.v. The frequency of the output signal, Fout.vi. Calculate the efficiency of the full wave rectifier expressed in percentage. vii. Sketch a graph of the input and output voltage against time.
Sketch current I vs, voltage V for the circuits below. The breakdown voltage of the Zener diodes are shown. Assume 0.6V for all diodes (including Zener diodes) in the forward bias region.
Draw circuit diagram with the help of diodes. The current vs voltage graph at the output of the circuit is shown below ...
1N4001, 1N4002, 1N4003, 1N4004, 1N4005, 1N4006 and 1N4007 For any of the diodes, describe with the aid of diagrams/illustrations its applications in an AC to DC Bridge rectifier power supply circuit. For your circuit show and describe how you are going to smooth out the ripple voltage that will be present.
1- Explain briefly with figure if exist, the Degenerate semiconductors. 2- When a diode is connected in a Reverse Bias condition, the overall result is a small ne current. Why?