In a car lift used in a service station, pressure is transmitted by an incompressible liquid from a small piston of circular cross section with a radius of r1 = 5.00 cm to a second piston of radius r2 = 15.0 cm. Calculate the minimum force that must be exerted on the smaller piston to lift a car weighing 13300 N.

In a car lift used in a service station, pressure is transmitted by an incompressible liquid from a small piston of circular cross section with a radius of r1 = 5.00 cm to a second piston of radius r2 = 15.0 cm. Calculate the minimum force that must be exerted on the smaller piston to lift a car weighing 13300 N.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A tremendous force is generated when waterfreezes into ice and expands in volume by 9.0%. Suppose a 1.000-m3cube of liquid water freezes into ice that is 1.000 m on a side by1.090 m tall. How many 68-kg students would the ice be able tolift? Determine this by calculating the amount of force on the top1.000-m2face that would be required to squeeze 1.090 m3of iceback to 1.000 m3, assuming all of the volume change occurs alongthe vertical direction
For a certain ideal gas R = 25.8 ft.lb /lb °R and k =1.09a. What are the values of cp and cv?b. What mass of this gas would occupy a volume of 15 cu ft at 75 psia and 80 °F?c. If 30 Btu are transferred to this gas at constant volume in (b), what are the resultingtemperature and pressure? include the diagram
2. There is a liquid having density of Np below a liquid of density p (N is an unknown constant). A piston of a rectangular cross section (width H into the page) is attached to a completely submerged sphere of density e/3 and volume 4/2H3, with a pulley attachment as shown in the figure. The piston surface has a 45° angle with respect to the horizontal direction and a 90° angle with the pulley cable. It is measured that the within the piston is atmospheric. pressure (a) Identify all the forces applied to the piston surface, and mark them on a free body diagram. Accurately indicate their points of action. (b) Evaluate N if all the forces applied to the piston surface balance. Air P/3 2H g Piston surface Np H
On Mars, the atmosphere is composed mainly of carbon dioxide. The value of the gas constant for the Martian atmosphere is 192 J/kg K, and the acceleration of gravity there is 3.72 m/s?. At the average level of the Martian surface, the average temperature is 228 K, the pressure is 774 Pa, and the density is 0.01768 kg/m3. surface, the average temperature is 225 K. What are the pressure and density at this altitude? At an altitude of 1km above the
In the figure shown below. Let X=2 cm, Y = 10 cm, specific weight of water = 9850 N/m?, Benzene density = 870 kg/m, Kerosine desity = 800 kg/m', Mercury specific gravity = 13.6. Neglect Air elevation. %3D GELLO Kerosine Air Benzene 40 cm 19 cm 20 cm Mercury- Water Determine the pressure difference (Pa) between points A and B. (PA-Pek
The figure shows a 50.-kg frictionless cylindrical piston that floats on 20 mol of compressed air at 45.°C. How far does the piston move if the temperature is increased to 600 °F? (This is an Isobaric process and the piston is at sea level under an atmospheric pressure of 101.3 kPa). The values given in the figure are: 50. Kg, 30.°C, and 10. cm.
Answer the following. A: When the pressure of liquid is increased from 3.5 MN/m² to 6.5 MN/m² its volume is found to decrease by (0.08) percent. What is the bulk modulus of elasticity of the liquid? B: An open cylindrical tank (1.2m) in diameter and (1.8m) deep is filled with water and rotated about its central axis at (60 r.p.m). How much liquid is spill and how deep of the water at the central axis.
A closed tank whose bottom is 18 inches in diameter is filled with three liquids: 4 inches of carbon tetrachloride (SG=1.59), 2 inches of water and 12 inches of syrup (SG=1.31). The air chamber in the tank is pressurized at 1296 psf. d. Apply the PANEL EQUATIONS to determine the magnitude, direction and location of the total hydrostatic force acting at the bottom of the tank.
Two chambers with the same fluid at their base are separated by a piston whose weight is 25 N, as shown in the Figure below. Calculate the gage pressures in chambers A and B. Please discuss the result comparing the gage pressures you obtained in chambers A and B. • Calculation errors will not be tolerated. Solution procedure will be evaluated with the exact results. Please be careful. Piston B Air Air p 50 cm 35cm 25 cm 38 cm E, Water 90 cm
For the manometer shown in the image, all fluids are at 20°C. If PB- PA = 90 kPa, determine the height H in centimeters. The specific weight of water is 9790 N/m³ and the specific weight of mercury is 133100 N/m³. Meriam red oil, SG = 0.827 Water 18 cm H 35 cm Numeric Response B Mercury
P1.) A closed cylindrical tank 1.5 m in diameter and 4 m long is completely filled with gasoline (sp.gr. = 0.82) and accelerated horizontally at 3 m/s². Find the total force acting at the rear wall and at the front wall of the tank. Find also the accelerating force on the fluid mass. Answer: 10.66 kN and F = 17.36 kN Subject: Fluid Mechanic Lesson: Relative Equilibrium of Liquids Fundamentals of Fluid Flow
A force, P, is applied to a piston with a mass of 15 kg and a diameter of 43 cm that rests on top of a cylinder containing water as shown. (The piston is free to move in the cylinder, but is sealed so no water can escape.) An open U-tube manometer is connected to the cylinder as shown. Determine the applied force, P in kN, if h1 = 68 mm and h = 100 mm. You can use the following data: the specific weight of water is 9.81 kN/m³ and the specific gravity of mercury is 13.546. Approximate your answer to three decimal places TU Piston Water Mercury