hollow titanium [G= 46 GPa] shaft has an outside diameter of D = 56 mm an tress in the shaft must be limited to 243 MPa. Determine: a) the maximum power P that can be transmitted by the shaft if the rotation s b) the magnitude of the angle of twist in a 830-mm length of the shaft when nswers: a) P = i b) = i kW.

hollow titanium [G= 46 GPa] shaft has an outside diameter of D = 56 mm an tress in the shaft must be limited to 243 MPa. Determine: a) the maximum power P that can be transmitted by the shaft if the rotation s b) the magnitude of the angle of twist in a 830-mm length of the shaft when nswers: a) P = i b) = i kW.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A portal frame PQR is subjected to uniformly varying load of maximum intensity 20 kN on an attached arm QT as shown in figure. Find the rotation at the hinge support R (in radian) E = 2.5 x 10 MPa I = 8 x 104 mm² Given: 20 kN/m P 3 m -1.5m- R 3 m
4. A copper bar 250 mm long and 50mmx50mm in cross-section is subjected to an axial pull in the direction of its length. If the increase in volume of the bar is 37.5 mm', find the magnitude of the pull. Take p-0.25 and E-100GPA. Answer: P-30 KN. 5. A steel bar 50mmx50mm in cross-section is 1.2 m long. It is subjected to an axial pull of 200 KN. What are the changes in length, width and volume of the bar, if the value of Poisson s ratio is 0.3 ? Take E as 200 GPa. Answer Al-0.48mm, Ab-0.006mm and AV-480 mm'. 6. A reetangular bar 500 mm long and 100mmx50mm in cross-section is subjected to forces as shown in figure. What is the change in the volume of the bar? Take modulus of elasticity for the bar material as 200 GPa and p-0.25. Answer :AV-137.5 mm'. 300 KN 100 KN 50 100 200 KN 500 mm
A hollow steel [E = 30,000 ksi] tube (1) with an outside diameter of 3.15 in. and a wall thickness of 0.25 in. is fastened to a solid aluminum [E = 10,000 ksi] rod (2) that has a 2.05 -in. diameter and a solid 1.00 -in. diameter aluminum rod (3). The bar is loaded as shown. Determine the deflection of point D with respect to the fixed support A.
The copper pipe has an outer diameter of 50mm and an inner diameter of 30mm. If it is fixed at A and three torques are applied to it as shown, solve the shear stress at section 1. A 200mm 250mm 3. 30 N-m 300mm 20 N-m 80 N m O 2.34MPA O 7.49MPA O 4.68MP O 3.74MPA
The outer and inner diameters of a 700mm long copper tube (E - 130GPA) are 100mm and 70mmm, respectively. If a torque of 10kNm was applied on the tube, solve the angle of twist. O 0.646 degrees O 0.722 degrees O 0.414 degrees O 0.517 degrees
A hollow shaft of 1m length is designed to transmit a power of 25kW at 625 rpm. The maximum permissible angle of twist in the shaft is 1degree. The inner diameter of the shaft is 0.4 times the outer diameter. The modulus of rigidity is 60 GPa. Determine the outside diameter of the shaft?
STRENGTH OF MATERIALS A boiler is constructed of 9mm thick steel plates that are fastened together at their ends using a butt joint consisting of two 9mm cover plates and rivets having a diameter of 10mm and spaced 60mm apart as shown. If the stream pressure in the boiler is 1.38MPa, determine (a) the circumferential stress in the boiler's plate apart from the steam, (b) the circumferential stress in the outer cover plate along the rivet line a-a, and (c) the shear stress in the rivets. 60 mm 0.78 m
The A-36 solid steel shaft is 2 m long and has a diameter of 65mm. It is required to transmit 60kW of power from the motor M to the pump P. Determine the smallest angular velocity the shaft in radian per seconds that can have if the allowable shear stress is 80 MPa.
1. A compound shaft consisting of a steel segment and an aluminum segment is acted upon by two torques as shown in Fig. P-316. Determine the maximum permissible value of T subject to the following conditions: Tst < 83 MPa, tal < 55 MPa, and the angle of rotation of the free end is limited to 6°. For steel, G = 83 GPa and for aluminum, G = 28 GPa. Steel 2T Aluminum 50 mm Ø 40 mm Ø 900 mm 600 mm
5) A flanged bolt coupling consists of 8 10mm diameter steel bolts evenly spaced around a bolt circle 300mm in diameter and 6 14mm diameter aluminum bolts on a concentric bolt circle of 200mm diameter. Determine the maximum torque that can be applied without exceeding a shearing stress of 50 MPa in the steel bolt and 30 MPa in the aluminum bolts. Use G = 83 GPa for steel and G = 28 GPa for aluminum.
A bracket connected to the flangé of a column through a group of rivets to transfer a load of 120 kN at an eccentricity of 150 mm as shown in the figure. The thickness of the bracket plate is 8 mm. Design the diameter of the rivets if the permissible stress in single shear is 100 MPa and in bearing 180 MPa. 120 kN 150- 4 p/n 30 60 60 60 G 60 30 90 +.
The drive shaft AB of an automobile is made of a steel having an allowable shear stress of 8 ksi. If the outer diameter of the shaft 2.5 in and the enginedelivers 200 hp to the shaft when it is turning at 1140 rev/min, determine the minimum required thickness of the shaft’s wall in inches.