5The cantilevered handle in the figure is made from mild steel that has been welded at the joints. For Fy=300 lbf and Fx = F₂ = 0, usesuperposition to determine the vertical deflection (along the y-axis) at the tip. The part dimensions are as follows: dAB= 0.75 in, dCD=0.625 in, t= 0.375 in, h = 2.25 in. See section 3-12 for the method of determining the angle of twist in a solid, rectangular cross section.COHintPrint6 indABBThe vertical deflection of the cantilever (along the y-axis) at the tip is2 in5 inin.dcp

Given:To find:Vertical deflection at the tip

he cantilevered handle in the figure is made from mild steel that has been welded at the joints. For Fy=300 lbf and Fx = F₂ = 0, uperposition to determine the vertical deflection (along the y-axis) at the tip. The part dimensions are as follows: dAB= 0.75 in, d 625 in, t= 0.375 in, h=2.25 in. See section 3-12 for the method of determining the angle of twist in a solid, rectangular cross se N dAB B h 2 in 5 in dcD

he cantilevered handle in the figure is made from mild steel that has been welded at the joints. For Fy=300 lbf and Fx = F₂ = 0, uperposition to determine the vertical deflection (along the y-axis) at the tip. The part dimensions are as follows: dAB= 0.75 in, d 625 in, t= 0.375 in, h=2.25 in. See section 3-12 for the method of determining the angle of twist in a solid, rectangular cross se N dAB B h 2 in 5 in dcD

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.9.7P: A steel riser pipe hangs from a drill rig. Individual segments of equal length L = 50 ft are joined...

See similar textbooks

Similar questions

The cantilevered handle in the figure is made from mild steel that has been welded at the joints. For Fy=150 lbf and Fx= Fz=0, use superposition to determine the vertical deflection (along the y-axis) at the tip. The part dimensions are as follows: dAB=1 in, dCD= 0.625 in, t= 0.375 in, h= 2.25 in. See section 3-12 for the method of determining the angle of twist in a solid, rectangular cross section. 6 in dAB t The vertical deflection of the cantilever (along the y-axis) at the tip is 2 in 5 in dcD
The cantilevered handle in the figure is made from mild steel that has been welded at the joints. The lengths are a=7 in, b=7 in, and c = 2.5 in. For Fx=0, Fy=275 lbf, and F₂=0. Use Castigliano's theorem to determine the vertical deflection (along the y-axis) at the tip. Note that when calculating the torsion strain energy of a noncircular cross section, Jis not the polar moment of inertia. Instead, use Eq. 3-41 to determine an equivalent Jeg for the solid rectangular cross section of member BC. The vertical direction at the tip is 1-india. tin in. in dia.
pin The solid 26-mm-diameter steel [E = 180 GPa] shaft supports two belt pulleys. Assume that the bearing at A can be idealized as a support and that the bearing at E can be idealized as a roller support. For the loading shown, determine the shaft deflection v at pulley D. Assume P = 670 N, Q = 540 N, LAB= 250 mm, Lac = 160 mm, LCD = 250 mm, LDE = 160 mm. B D E C LAB Answer: Vp= M LBC LCD mm. LDE
Part A A simply supported shaft is shown in the figure below. Assume the following data: a = 16 in, b = 18 in, l = 20 in, P = 1000 lb, Tmin=0 lb-in, Tmax=2000 lb-in. The steel shaft diameter is 1.75 in. Determine the maximum deflection in bending of the shaft shown in the figure. Express your answer in inches to three significant figures. Enter positive value if the deflection is upward and negative value if the deflection is downward. Submit Previous Answers Request Answer Part B ΗΠΙΑΣΦΗ * Incorrect; Try Again; 4 attempts remaining vec Omaz = Submit bearings are self-aligning so act as simple supports Determine the magnitude of the maximum deflection in torsion of the shaft shown in the figure. Express your answer in degrees to three significant figures. ΑΣΦΗ ΠΕ vec Previous Answers Request Answer ? in ?
The figure shows a cantilever of length L=4 m consisting of steel angles size of 100 x 100 x 12 mm mounted back to back. The cantilever is subjected to a point load P=3500 N acting at a=1.5 m and a distributed load w=1000 N-m-¹ NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Gr Find the deflection at B The deflection at Bis- a W mm. P B x B
b) The shaft shown in figure 6 supports the three pulley loads. The shaft is made of steel and has a diameter of 30 mm. The bearings at A and B exert only vertical reaction on the shaft. Determine the equation of the elastic curve equation (equation of the deflection along the length of the shaft) and find the deflection at x = 0.5m. Given: E = 200 GPa, 1 = n²/4 -250 mm-250 mm-250 mm---250 mm Figure 6 150 N 60 N 150 N
F A 1 m- 2 m 6 m B 3 m 1.5 m The space truss above is supported by ball-and-socket joint at points A, B, and E. A single force F = {-200i +300OJ +50k} N is applied at point D. Take the following: • UDA = {-0.267i -0.802j -0.535k} • UDB = {+0.923i +0.231j -0.308k} • uDc = {-0.371i +0.557j -0.743k} Which of the following is closest to the force in member DB? -265 N (C) O -221 N (C) 281 N (T) 209 N (T)
Problem 5 A 1/4-in-thick beam OAB is fixed to the wall at one end and supported by a 1/2-in- diameter rod at the other end, as shown in the figure. in F The beam and the rod are both made of 1018 CD steel dia. with E = 30 x 106 psi and Sy = 54 x 103 psi. The 1500 lbf is applied as shown. Determine the 12 in 2 in -in thick load F deflection at point B. A -12 in 6 in Hint: The cases below can be helpful. 1 Cantilever- end load 2 Cantilever-intermediate load Fx Fx YAB= 6EI (x - - 3a) y = (31) 6EI F Fa 6EI Увс (a - 3x)
The figure shows a cantilever consisting of steel angles size 100 x 100 x 12 mm mounted back to back. Using superposition, find the deflection at B and the maximum stress in the beam. 3 m 2.5 kN - 2 m I kN/m explain every step and define every equation. neat writing.
The cantilever shown in the figure consists of two structural-steel channels size 3 in., 5.0 lbf/ft. Using superposition, find the deflection at A. Include the weight of the channels. Take the magnitude of force (F) to be 145 lbf. Take Las 53 in and was 4.8 lbf/in. L W 46 The deflection at point A is A 0.11 inch in the downward ✓ direction.
A round steel bar having a cross section of 0.5 in.² is attached at the top and is subjected to three axial forces, as shown in the figure. Find the deflection of the free end caused by these forces. Plot the axial force and the axial deflection 2-8. diagrams. Let E = 30 × 106 psi. Ans: Amin = 0, Amax = 0.040 in. 36 4 k 24" 12" 2 k 8 k PROB. 2 – 8
A flanged wooden shape is used to support the loads shown on the beam. The dimensions of the shape are shown in the second figure. Assume LAB = 9 ft, LBc = 2 ft, LcD = 3 ft, LoE = 2 ft, Pc = 1920 Ib, PE = 2070 Ib, wAB = 810 Ib/ft, b1 = 8 in., b2= 2 in., b3= 6 in., dz = 2 in., d2= 11 in., d3= 2 in. Consider the entire 16-ft length of the beam and determine: (a) the maximum tension bending stress or at any location along the beam, and (b) the maximum compression bending stress oc at any location along the beam. PC PE WAB B |C D E LAB LBC LCD LDE b1 d |d2 - bz dz bz Answers: (a) or = i psi. (b) oc psi.