Hand Sanitizer (70% propanol gel) needs to be transported on a floor in a hospital from a central location per floor. The room farthest from the source is 17.5-m away. The hand sanitizer enters the tubing at 20°C and 275 kPa absolute and exits the tubing at atmospheric conditions. The tubing can Flowrate/velocity Calculation. Hand sanitizer be considered smooth; however, there are two (2) 90° curved elbows and four (4) Tee Run throughs, and one (1) foot value (Refer to the Loss for Fittings table in Canvas). The density of the hand sanitizer is 955 kg/m3 and the viscosity is 4.5 cP. What is the flow rate that can be obtained if the tubing diameter is 4.5-mm? K-values. Below is table of typical K-values for various fitting types.FittingТурesKStandard (R/D = 1)0.3545° ElbowLong Radius (R/D = 1.5)0.2Standard (R/D = 1)0.7590° Elbow CurvedLong Radius (R/D = 1.5)0.4590° Elbow Square or Mitred1.3180° BendClose Return1.5Tee, Run ThroughBranch Blanked0.4Tee, as ElbowEntering in runTee, as ElbowEntering in branch1Tee, Branching FlowCoupling0.04Union0.04Gate valveFully Open0.173/4 Open0.9 e = 20°1.5640°17.3%3!e = 60°206e = 5°0.24e = 10°0.52Butterfly valvee = 20°1.54e = 40°10.8e = 60°118SwingCheck valveDisk10Ball70Foot valve15Disk7Piston15Water meterRotary (star-shaped disk)10Turbine-wheel6.

Inlet pressure= P1= 275 KPa density of fluid= ρ=955 kg/m3 tube diameter = d= 4.5 mm diameter of pipe…

Hand Sanitizer (70% propanol gel) needs to be transported on a floor in a hospital from a central location per floor. The room farthest from the source is 17.5-m away. The hand sanitizer enters the tubing at 20°C and 275 kPa absolute and exits the tubing at atmospheric conditions. The tubing can Flowrate/velocity Calculation. Hand sanitizer be considered smooth; however, there are two (2) 90° curved elbows and four (4) Tee Run throughs, and one (1) foot value (Refer to the Loss for Fittings table in Canvas). The density of the hand sanitizer is 955 kg/m3 and the viscosity is 4.5 cP. What is the flow rate that can be obtained if the tubing diameter is 4.5-mm?

Hand Sanitizer (70% propanol gel) needs to be transported on a floor in a hospital from a central location per floor. The room farthest from the source is 17.5-m away. The hand sanitizer enters the tubing at 20°C and 275 kPa absolute and exits the tubing at atmospheric conditions. The tubing can Flowrate/velocity Calculation. Hand sanitizer be considered smooth; however, there are two (2) 90° curved elbows and four (4) Tee Run throughs, and one (1) foot value (Refer to the Loss for Fittings table in Canvas). The density of the hand sanitizer is 955 kg/m3 and the viscosity is 4.5 cP. What is the flow rate that can be obtained if the tubing diameter is 4.5-mm?

Welding: Principles and Applications (MindTap Course List)

8th Edition

ISBN:9781305494695

Author:Larry Jeffus

Publisher:Larry Jeffus

Chapter20: Shop Math And Weld Cost

Section: Chapter Questions

Problem 24R: What is a dimensioning tolerance?

See similar textbooks

Similar questions

In a limit system, the following limits are specified for a hole and shaft assembly: Hole = 30 (+0.02 )/(+0.00 ) mm and Shaft = 30 (-0.02)/(-0.05) mm. Determine the basic size, tolerance and allowance, maximum and minimum clearances, type of fit.
Calculation of Limits using ANSI B4.1 Standard Tables, when one of the design Features Exists. When calculating the limit tolerances for features that mate with purchased parts, the purchased part size must be known. This may be obtained be requesting a drawing from a vendor or, a caliper or micrometer can be used to obtain an accurate size. A shaft diameter of 1.2500" is to be pressed into a part using a FN3 interference (force) fit. Limits of size for the shaft diameter are 1.2500" and 1.2495". Determine the Limits of the hole diameter. Show all work.
Q1/B) Match between Column A & B. A 1 Cutting Fluids 2 HSS 3 Serrated or segmented chips 4 Vertical shaper 5 Milling 6 Chip load 7 continuous Chip with BUE 8 Slitting 9 Electron beam machining 10 Ultrasonic machining B Horizontal milling machining vibration E Ductile material machined at low cutting speed F Interrupted cutting operation G Emulsified Oils H Cyclical formation of alternating high shear strain followed by low shear strain 1 Slotter J Feed per cutter tooth A Good toughness vacuum B C D Answer from A
The toleranced diameter of a hole is given as 0.990"/1.010" and the size of the mating pin is given as 0.985"/0.980 37. What is the maximum clearance for this fit? 0.030" 0.020" 0.025" c) 0.010" (P 38. What type of fit is this? transition b. clearance interference d. none of the above 39. A fit can be determined by specifying: upper limit b. allowance max. clearance b& c all the above TE d. 40. A fit is specified as 60H1109 in Metric unit. What is the tolerance grade for the shaft? 60 a. b. 9 11 d. none above
A shaft has to be assembled with a hole. The shaft has maximum limit 59.762 and minimum limit 59.56, and the hole has a maximum limit 60.24 and a minimum limit 60.04, compute the following: Tolerance of the shaft is Tolerance of the hole is Shaft size according to MMC = Shaft size according to LMC = Maximum clearance = Minimum clearance = Hole size according to MMC = Hole size according to LMC =
For the following hole and shaft assembly, determine hole and shaft tolerance and type of fit. Hole = 20 (+0.025 )/(+0.000 ) mm and Shaft = 20 (+0.080)/(+0.005) mm.
16q A slip gauge setting height of 65.215mm is observed and an angle of 480 is found during the precise angle measurement of a workpiece in a workshop. Find the length of the Sine Bar used in mm= (Enter at-least 4 digits after decimal points)
A solid steel shaft with a diameter of 130 mm must be press-fitted in a journal bearing (Figure 1) with an inlet and outlet diameters of 130 and 145 mm, respectively. Both solid shaft and journal bearing require rigidity and alignment with an accuracy of the location. Consider a journal bearing inlet diameter as the basic size. Oudet Bearing Inlet Journal Figure 1 AJournal Bearing
Thread Fits and 7. Define fit, allowance, tolerance, and limits. 8. How are external UNC threads classified? 9. Name and describe three classifications of UNC fits. 10. How are thread fits designated for the ISO threads? Classifications 11. Why was the ISO metric system of threads adopted? 12. Describe a thread designated as M 56 X 5.5. 13. Name five thread forms used in North America and state the included angle of each. 14. What are the principal differences between the American and Unified threads?
3. If there is a 0.10 mm accuracy error for all measured parameters at Instruction 1, determine the true volume of the allen bolt. Also, comment on the difference between volume calculated by measured data and volume calculated by true data.
1. AISI steel designation for plain carbon steel. 2. In GD&T, what does this indicate | |? 3. A fit wherein the size of the diameter of the internal member is greater than the external member. 4. Brass is an alloy of copper and 5. A type of tolerance where the size of a part is permitted to be either larger or smaller than the given or specified dimension.
2 5 What is the shape and size of this tolerance zone? 1.25 0.50 Diam +/-0.002" 0.010