Gasoline flows steadily downward through the pipe shown in the figure below. Viscous effects are negligible, and the pressure gage indicates the pressure is zero at point (1). Determine (a) the flowrate and (b) the pressure at point (2). (a) Q = (b) p2 = 2.1ft 3.1ft (2) •(1) 18 -0.12 ft -0.1 ft -free jet ft³/s lb/ft²

Gasoline flows steadily downward through the pipe shown in the figure below. Viscous effects are negligible, and the pressure gage indicates the pressure is zero at point (1). Determine (a) the flowrate and (b) the pressure at point (2). (a) Q = (b) p2 = 2.1ft 3.1ft (2) •(1) 18 -0.12 ft -0.1 ft -free jet ft³/s lb/ft²

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

oll, s = 0.80 kerosene,s = 0.82 A manomoter is used to moasuro tho s = 0.0012 pressure of air in shown. Solve the pressure at point A given the following hoights: the pipe as Air = 0.35 m,h2 = 0.38 m, h, = 0.20 m, %3D h4 = 0.50 m, hs = 0.10 m, h6 = 0.30 m hz hy h3 ho Water Mercury Mercury
Crude oil (with specific weight γoil = 55 lb/ft3 ) is pumped at a rate of 400 gallons per minute from a test separator at A to the stock tank shown using a pipe that has a diameter of 4 inches. The pressure at A (to the left of the pump or prior to the pump) is 4 psi and the stock tank is open to the atmosphere. The friction head loss along the entire length of the pipe from A to B is 45 inches. Note that 1ft3 = 7.48 gallons. (a) Determine the velocity in the pipe. (b) Determine the head gain, ℎ??, delivered by the pump to the flow. (c) Determine the power required to run the pump if it is 90% efficient.
4. The figure shows two cylinders of diameter D and 2D, connected to each other and containing an incompressible fluid. The two cylinders are filled with leak-proof pistons of weight W1 and W2 as shown. The releationship between W1 and W2 is a) W2 = W1 b) W2 = 0.5 W1 c) W2 = 5 W1 d) W2 = 0.4 W1 20 k- 5. A flat plate is sliding at aconstant velocity of 5 m/s on a large horizontal table. A thin layer of oil ( of absolute viscosity 0.4 N.s/m2) separates the plate from the table. To limit the shear stress in the oil layer to 1 kpa, the thickness of the oil film (mm) should be most nearly to a) 0.2 b) 20 c) 1.6 d) 1.85
FLUID FLOW IN PIPES I. Proving. SHOW THAT 1. R = A/P → D = 4R fyv² 8g 2.T= y (hf)D 4L
Surface Nozzle Fluid stream Surface Nozzle Fluid stream E F, 2 F1 equals 2 F2 O F1 greater than 0 and F2 equals 0 F1 equal F2/2 O F1 equals 0 and F2 is greater than 0 F1 equals F2 O
O -0.13 Darcy Experiment A set-up of Darcy Experiment involves measuring the pressure head at two piezometers separated a distance, L. Given the set-up shown, determine the hydraulic gradient if the hydraulic head at (1) is 24 inches, hydraulic head at (2) is 11 inches, and the travel distance is 100 inches. O 7.7 O -7.7 (1) O 0.13 e - - - -
Liquids A, B and C, in the containers shown, have SG of 0.80, 1.00 and 1.60 respectively. What is the pressure at the bottom of the tank? hA EL. 8 A (SG = ha EL. 6 B (SG = hc EL. 2 C (SG = EL. O a. 85.382 kPa O b. 86.328 kPa c. 86.382 kPa d. 89.328 kPa
1. [Ch4 – 2] A hydraulic oil with the absolute viscosity of 0.09 N.s/m² and specific gravity of 0.9, is flowing in a 30-mm- diameter pipe at a velocity of 6 m/'s, detemine: a. The Reynolds number? Is the flow laminar or turbulent? b. The head loss due to friction in units of bars for a 100-m length of smooth pipe. 2. [Ch4 - 2] The kinematic viscosity of a hydraulic oil is 0.0001 m/s. If it is flowing in a 20-mm- diameter commercial steel pipe, find the friction factor for: a. The velocity of 5 m/s b. The velocity of 50 m/s
3. From d figure below, if the atmos. pressure is 770mm of Hg, fınd: a) Rm if the pressure at B is 797mm of Hg abs. b) If Rm=58mm, find the pres. at B in meters of water abs. Hg A Air Oil Sp. Gr. = 0.8 R. Water 750 mm 80 mmy +B 200 mm ....
2. A tank and piping system are shown below. The total length of PVC pipe is 2500 ft and discharges water into the atmosphere. The pipeline has an open globe valve and four threaded elbows; h1 = 10 ft and h2 = 45 ft." a. If the discharge is 0.5 cfs, what NPS should be used for the PVC pipe (ks = 0.00006 inch). b. What is the pressure at A, the midpoint of the pipeline? c. Draw the EGL and HGL. h2 Water T = 10°C (50°F) Globe valve
Water backs up behind a concrete dam as shown in figure Leakage under the foundation gives a pressure distribution under the darri as indicate If the water depth, h, is too great, the dam will sopple over about its toe (Point A) For the dimensions given, determine the factor of safety agarest overtuming moment if L-120 fh and h - 50 n. Base your analysis on a unit length of the dam The specific weight of the concrete is 150 ib/tt3 Water
IL. Q2-1 [5 Points]:A fluid has an absolute viscosity of 0.048 Pa-s and a specific gravity of 0.913. For flow of such a fluid over a solid flat surface, the velocity at a point 50 mm away from the surface is 1.467 m/s. Calculate the shear stresses at the solid boundary (N/m) 0.67 1.2 3.35 0.97 1.41 3.03 1.35 1.79