For the project, its data shown below find: Time in weeks that gives a probability of %97.5 Probability of finishing the project 4 weeks more than TE Probability of finishing the project 3 weeks less than TE

For the project, its data shown below find: Time in weeks that gives a probability of %97.5 Probability of finishing the project 4 weeks more than TE Probability of finishing the project 3 weeks less than TE

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: In a site consisting of normally consolidated clean sands,the water table is at 10 ft depth. The…

A: Given:- The depth of the water table = 10 ft The average unit weight of the sand above the water…

Q: Describe the applications, limitations and appropriateness of each method. Shears and Moments using…

Q: Determine the coordinates of the centroid of the lines shown with respect to the indicated X and Y…

Q: The values of liquid limit, plastic limit and shrinkage limit of a soil were reported as below: W₁ =…

Q: Provide 7 photos of roundabouts and explain their purpose and explain how ellipses are applied in…

A: Roundabouts- Compared to traffic lights and stop signs, roundabouts are a safer option. Drivers must…

Q: A summit curve is formed at the intersection of 3% upgradient and 5% down gradient. To provide a…

Q: Q2) Figure Q2 shows a 30-kg block is connected to block B through a frictionless pulley. The…

A: Given:- The mass of the block A = 30 kg The coefficient of static friction = 0.35 To determine:- i)…

Q: 50. WH SO 3 k

Q: A cantilever beam, 4m long, carries a uniformly distributed load our total length. If the slope at…

A: Given- Cantilever beam span L=4 m, Slope θ=1.5o Deflection at the free end = ?

Q: Problems (5.2) Figure below shows a conical vesse! having its outlet at A to which a U-tube…

Q: 50. What should be the height (m) of a lighthouse, so that it can be visible from a distance of 3…

Q: How do the principles of kinematics influence innovations in transportation?

A: Principles of kinematics- Position, displacement, velocity, velocity, and acceleration are the five…

Q: Question- A smooth two-dimensional flat plate is exposed to a wind velocity of 70 km per hour. If…

A: Given- Wind velocity V=70 km/hr, Reynold's No.- Rex=3×105, kinematic viscosity- ν=1.49×10-5 m2/s, It…

Q: A fluid of specific gravity 0.8 and dynamic viscosity 15 x 10-4 Pa.s is flowing in a 15 mm diameter…

Q: a. Determine the centroid with respect to the indicated X and Y axes of the area shown. b. Determine…

A: For the plane diagram, the moment of inertia for centroidal axis and reference axis x and y can be…

Q: An aluminum tensile test specimen has a diameter, do = 25 mm and a gauge length of Lo = 250 mm. If a…

A: Given : do = 25 mm Lo = 250 mm Force = 175 kN Elongation of Gauge length = 1.25 mm This is a…

Q: Provide illustration and label accordingly The uniform slender rod AB shown of weight W is…

A: The given data is shown below: θ=30°f=0.3

Q: Design a welded plate girder of span 30m to carry imposed load of 25kN/m. Avoid use of bearing and…

A: Span=30 mImposed load=25 kN/mSteel grade= Fe 415 To design: welded plate girder

Q: For a beam cross section W = 230 mm, effective depth = 500 mm, the number of reinforcement bars of…

A: Given- width w=230 mm, Effective depth d=500 mm, 12 mm dia bars, It is needed to find the number of…

Q: The rigid bar EFG is supported by the truss system shown. Determine the cross- sectional area of…

Q: 2) A beam loaded with both transverse and longitudinal loads as show. his beam loading is typical of…

Q: Calculate the error (mm) in the linear measurement of offset, if the length of the offset is 80 m,…

A: Given: The length of the offset is 80 m. The accuracy in the measurement of the length is 1 cm in 60…

Q: 3. Find the moment at A (fixed) for the following structures. E= 10,000 ksi, and I = 100 in

A: ###### FINDING MOMENT AT FIXED END SUPPORT A ##

Q: A RIGID BAR "AB" ATTACHED TO TWO VERMCAL RODS IS HORIZONTAL BE FORE LOAD "P" IS APPLIED. DETERMINE…

A: Given Data Length of steel = 2.4m = 2400 mm Length of aluminum = 1.4m = 1400 mm Modulus of…

Q: what is coompetitive advatage

A: A company's ability to produce services or goods better, more efficiently, or for less money than…

Q: The rigid bar EFG is supported by the truss system shown. Determine the cross-sectional area of…

Q: The column section shown above is reinforced with equal number of 20 mm bars с 1. on each face.…

A: Answer 1) Calculation of neutral axis 'c' We know that at balanced condition strain at extreme…

Q: A mild steel bar is subjected to an axial force P, resulting in an axial stress ♂ =100N/mm² What…

Q: Question 1 Determine the maximum slope and deflection. A is fixed support B is free end. 1. Solve it…

A: As per guideline we can solve only one question

Q: Describe the applications, limitations and appropriateness of each method. Cantilever Three-Moment…

A: Answer Cantilever Method Appropriateness Since this method considers that the structure behaves…

Q: The degree of static indeterminacy of a rigid jointed frame PQR supported as shown is R EI 145° .90⁰…

A: Given- Rigid jointed frame PQR- It is needed to find the degree of static indeterminacy Ds.

Q: Determine the moment of the force of Fig. CB. (b) Point B. with respect to: (a) Line

A: Given : This is a problem of solid mechanics where we have to find the moment of force for : a )…

Q: CASE: A rectangular beam has the dimensions (see Fig.1) b = 15 in.,h = 30 in., and d = 27.37 in. and…

A: Given: b = 15 in h = 30 in d = 27.37 in fc = 4 ksi fy = 60 ksi n = 475 psi M = 45 kips-ft M = 110…

Q: Fig. shows a bar. Find the reaction produced by the lower support on the bar. Take E = 200GN/mt.…

A: First we summarise the given data : E = 200 GN/m2 To find : The stresses in the bars.

Q: Use A992 steel and select a W14 shape for an axially loaded column to meet the following…

A: Given:- The length of the column = 22 ft Both ends are pinned A bracing is provided in the weak…

Q: XXe A concrete beam is post-tensioned by a cable carrying a pre-stress of 900 N/mm². At the jacking…

A: Given data- A post-tensioned concrete beam- Prestress = 900 N/mm2, Slip = 8 mm, Es=210 kN/mm2, To…

Q: For the area shown, do the following: a. Determine the centroid with respect to the indicated X and…

A: Given To find a. The centroid with respect to the indicated X and Y axes of the area shown b. The…

Q: Determine the reactions and draw the shear and bending moment diagrams for the structure shown using…

Q: Homework: Determine the displacement and slope of point (C) of the beam shown below. Take E 200 GPa,…

Q: A designed road is to be constructed on a terrain with a uniform ground slope. The road contains a…

A: Answer (a) Calculation of final cross section data Draw the cross section based on given data At…

Q: Consider the cross-section shown below [a = 20 in.]. The distance from the centroid to the bottom of…

A: Solution:

Q: The compound beam is pin supported at C and supported by a roller at A and B. There is a hinge (pin)…

A: Given data in question Load 4k, 1k & 27 k Angle 30° Span 19 ft Internal hinge at D Statically…

Q: Two cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that the…

A: Given data- Normal stress in AB- σAB=175 MPa, Normal stress in BC- σBC=150 MPa, To Find- The values…

Q: Question alt A (200 x 100 x 50) mm³ steel block is subjected to a hydrostatic pressure of 15 MPa.…

A: Given- Size of block- 200×100×50 mm3 Poisson's ratio μ=0.3 Young's modulus E=200 GPa, Hydrostatic…

Q: = Fig shows a 700 mm length of aluminum alloy bar is suspended from the ceiling such away to provide…

A: A ) Given data : Length of Aluminum alloy bar = 700 mm Length of Steel Bar = 250 mm Aal = 1250 mm2…

Q: ation 1 A 500 cubic-centimeter solid having a specific gravity of 2.05 is submerged in two-liquid…

A: Given Volume of solid Vs=500 cm3Specific gravity of solids s.gsolid=2.05Specific gravity of mercury…

Q: Determine the force in each member of the truss 2+A m A B 1+B+ 5 kN -2 m- E OF CO C -2 m. S Y KN 11.…

A: Given Data Find the support reaction and member force in AG, AF, AB, GF, FE, BE and BC.

Q: Question 12. Determine the net area (An) and effective net area (A.) for the channel tension member…

A: Given,Bolt diameter=58 inC6×10.5A36To determine,Net area An and effective area Ae

Q: A water-treatment plant is to process 30,000 m³/d. The rapid mixing tank will blend 35mg/l of alum…

A: Given,Q=30000 m3/dblend of alum=35 mg/LDetention time=2 minTo determine(a) Quantity (Kilograms per…

Q: A helical spring, with small slope of helix, is supposed to transmit a maximum pull of 2 kN and to…

A: Given- Maximum pull= 2 kN, Extension of 10 mm for 400 N load, Mean diameter is 100 mm, G=80 GPa,…

Concept explainers

Quantity takeoff

Quantity takeoffs (QTO) are precise estimates of the materials and labor costs required to finish a construction project. During the pre-construction phase, an estimator prepares them, breaking down the project into smaller, more manageable parts that are easier to evaluate. These measurements are used to prepare a construction scope bid. Estimators examine the drawings, specifications, and models to figure out different quantities and their costs. Since, the components, their quantity, and price are all included in the model, quantity take-off can be done automatically using Building Information Modelling (BIM). The time taken for completing a construction project can be reduced by the use of quantity takeoff. These takeoffs are also called material takeoffs and construction takeoffs.

Question

Q2: For the project, its data shown below find:
●
Time in weeks that gives a probability of %97.5
Probability of finishing the project 4 weeks more than TE
Probability of finishing the project 3 weeks less than TE
Act.
1-2
2-3
2-5
2-4
3-4
3-7
5-6
6-7
4-7
0
8
4
7
7
4
7
10
10
4
M
10
5
9
6
8
14
14
5
P
24
12
21
11
8
15
24
24
12

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Concept

VIEW

Solution

VIEW

Answer

VIEW

Step by step

Solved in 3 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Homework#3 The ages of the 112 people who have a car injured are classified as follows: Class 0 - 9 10 - 19 20 - 29 30 - 39 40 - 49 50 - 59 60 - 69 Frequency 20 21 23 16 11 10 3 70 - 79 80 - 89 Find: 1- The mean 2- The median 3- The mode 4- Show the histogram graph. Homework #4 From the Previous example in Lec.5 Find : 1- The median 2- The Mode 3- The relative Frequency Histogram 1- The polygon frequency. Frequency Mid Class 52.5 58.5 64.5 Classes 50 - 55 56 - 61 3 3 62 - 67 68 - 73 74 - 79 Total 3 70.5 76.5 13
Q3) For the following schedule, draw the node network, perform the CPM calculations, mark the critical path, and complete the table. Activity A В BCD с EFG I H Duration IPA 7964 426 3 A A B B B, C D E F, G Lag 2 3 ES EF LS LF TF FF
Q2: Draw the network diagram (Job-on-arrow) and find the shortest possible time to finish the whole job by calculating ES, LS, EF, LF, TF, and finding the critical path, knowing that: Operation Duration in weeks A В C E F I 4 6. 2 8. 3 10 Preceding operations A A В В C+F D ---
Q3: For the information shown below, draw the network diagram by using AOA method and prepare a table containing ES, EF, LS, LF, TF, and critical path. Activity Preceded A В D E F G H I J K L M в D С, G F, H, I, К, L A A A В B E E by Duration J 4 1 3 3 3 2 3 1
Question 4: Determine the amount of time in weeks that gives a probability of 97.5% until the seventh event in the following grid, and then find the following: What is the probability of completing the project with a period less than TE by 4 weeks What is the probability of completing the project with a period of more than TE by 2 weeks Act. 1-2 2-3 2-5 2-4 3-4 3-7 5-6 6-7 4-7 0 8 4 7 7 4 7 10 10 4 M 10 5 8 9 6 8 14 14 5 24 12 21 11 8 15 24 24 12
For the project data in Table below, draw an AON Network for the project? Activity Duration predecessor A 8. C E A В, Е С. F F 8. H D, G I 17 J 10 G, I ABCA
Activity A (BCDEFGH 4. For the following schedule, draw the node network, perform the CPM calculations, mark the critical path, and complete the table. с Duration 6 2 8 5 3 6 5 2 Q Search U IPA A A, B B D, E C, D F, G ES O EF 0 LS ** LF TF FF 4 1 F*
Given the AON network in the Figure, determine the ES, EF, LS, LF, TF, and FF of each activity. Also indicate the critical path on the network. Start to Start SS 7 FS8 S 3 F K FF 3 10 4 10 S 4 S FF 3 FS 1 E H J L A B 5 2 10 4 4 FF 4 G S 5 3 S 3 D I 4 9
Problem 2 From the following table of information: a) Draw the precedence diagram; b) What is the probability that the project can be completed om 24 days or less? In 21 days or less? Activity Precedes Time in days Optimistic Time Most likely Time Pessimistic Time A C 5 6 7 H. 8 11 E 6 11 CIV 417/CPM THE PROBABLE TIME ESTIMATE Activity Precedes Time in days Optimistic Time Most likely Time Pessimistic Time D F 12 15 E END 5 7 10 F G 5 7 G END 3 4 7 H 4 4 END 7 8
Q/ For the project data in Table below, answer the following questions: a) Draw an AOA network of the project and Perform forward path and backward path calculations with critical path identification? b) What are the effect of delaying activities C by 5 days, G by 3 days and D by 5 days? Duration Immediate Activity (day) predecessor A 9. В 11 A C 6. A D 8 В, С E 6. A F 11 D,E G 7 C H 9. F, G I 7 H J 1 H
Homework#3 The ages of the 112 people who have a car injured are classified as follows: Class Frequency 20 0 - 9 10 19 20 - 29 30 - 39 21 23 16 40 - 49 11 50 59 10 60 69 7 70 - 79 80 - 89 3 1 Find: 1- The mean 2- The median 3- The mode 4- Show the histogram graph.
In 200 words, What should be observed/analyzed in performing AASHTO T 248? upvote guaranteed