For the pin-joined truss shown in Figure 2, 1) Find the reactions at A and J; 2) Determine the axial force in each of the 7 members connected at E, and state if these members are in tension or compression. 40 KN ↓ 30 kN B A 5 m 40 kN D E F 20 KN 5 m 40 KN G H 60 KN 5 m 40 KN I J 5 m T 5 m

For the pin-joined truss shown in Figure 2, 1) Find the reactions at A and J; 2) Determine the axial force in each of the 7 members connected at E, and state if these members are in tension or compression. 40 KN ↓ 30 kN B A 5 m 40 kN D E F 20 KN 5 m 40 KN G H 60 KN 5 m 40 KN I J 5 m T 5 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question 7: For the pin-joined truss shown in Figure 7, 1)Find the reactions at A and B; 2)Determine the axial force in members CE, DE, DF and CD. State if these members are in tension or compression. H I K G E C A 4 m F D B 4 m J 4 m L 4 m M 10 KN 20 kN 4 m 4 m 4 m
In the figure shown, the Aluminum member (AC) with a diameter of 1.125in is connected with the steel member (CD) of a diameter of 1.625in from point C, these members are restrained by rigid supports at A and D. Find: 1) The values of reactions at supports A + and D 2) The deformation at point C () E = 10.4 x 10°psi E = 29 x 10 psi 1SKips 14Kips A C 8 in 10 in 10 in
describe the load acting on the beam determine the reactions RA and RB at the supports determine the maximum bending moment Mmax
the truss shown in the below figure is supported by a hinge at A and a link BC. Determine the components (magnitude and direction) of the reactions at A and B
In the truss shown below, determine the reactions at A and B, as well as forces in each of the 5 members. (Hint: It will make our job easier if we identify zero-force members first.) 3 m D 150 N + 4 m B 6 m
The truss in the figure is loaded by four external forces as shown below. Knowing that P1= 3 kN, P2-4 kN, P3-6 kN and P4=2 kN, a= 3 m and h=2 m, you are required to: h P1 P2 a H B members GH, BG, BC. I P3 G C P4 F D a --- a -- a a) Determine the reactions at the supports A and E. b) Using the method of joints, determine the forces of the members at joint A. c) Using the method of joints, determine the forces of the members at joint E. d) Using the method of sections, determine forces on members GF GC, CD. e) Using the method of sections, determine forces on P1 Note: You are required to draw the FBD and apply the equilibrium equations for each case. E
2. Find the force acting in Bar AC,CE & CD of the compound Truss and the reactions at A & F as shown in the below figure. 180 lb 540 lb 10 10 B D 10 A E F 18' RA RF
The members of a truss are pin connected at joint 0. Set 0 = 60°. 5 kN 70 30° 7 kN Magnitude of F1: 4.31 kN Magnitude of F2: [ Choose ]
Zero-Force Members are structural members that support No loading but aid in the stability of the truss. Tips on getting the zero-force members: 1. there is no external load or reaction at that joint 2. Insufficient structural members to satisfy or "balance" the system: Summation of forces along the horizontal and vertical 3. two of the members are collinear As shown in the figure, structural members of zero-force members can be noticed through observation. H G F A D E At a glance, it can be inferred that the member FG and FE are zero force members, because: First, there is no external load applied on the joint Secondly, taking the Joint F, if Summation of Forces along horizontal = 0 is executed, only the member FG has the horizontal component, or the "ability" to "balance" the system, and if Summation of Forces = 0 is executed, the member FE has the vertical component, or the "ability" to "balance" the system only. along vertical Aside from members FG and FE, through observation,…
Use the method of joints to calculate the forces in all the members of the truss shown in Figure 2 below. 20KN 30⁰ C Rc B RB 60⁰ A 5m Figure 2
Zero-Force Members are structural members that support No loading but aid in the stability of the truss. Tips on getting the zero-force members: 1. there is no external load or reaction at that joint 2. Insufficient structural members to satisfy or "balance" the system: Summation of forces along the horizontal and vertical 3. two of the members are collinear As shown in the figure, structural members of zero-force members can be noticed through observation. Load P G Н, F A B D E At a glance, it can be inferred that the member FG and FE are zero force members, because: First, there is no external load applied on the joint Secondly, taking the Joint F, if Summation of Forces along horizontal = 0 is executed, only the member FG has the horizontal component, or the "ability" to "balance" the system, and if Summation of Forces = 0 is executed, the member FE has the vertical component, or the "ability" to "balance" the system only. along vertical Aside from members FG and FE, through…
Zero-Force Members are structural members that support No loading but aid in the stability of the truss. Tips on getting the zero-force members: 1. there is no external load or reaction at that joint 2. Insufficient structural members to satisfy or "balance" the system: Summation of forces along the horizontal and vertical 3. two of the members are collinear As shown in the figure, structural members of zero-force members can be noticed through observation. Load P Н, G F A D E At a glance, it can be inferred that the member FG and FE are zero force members, because: First, there is no external load applied on the joint Secondly, taking the Joint F, if Summation of Forces along horizontal = 0 is executed, only the member FG has the horizontal component, or the "ability" to "balance" the system, and if Summation of Forces = 0 is executed, the member FE has the vertical component, or the "ability" to "balance" the system only. along vertical Aside from members FG and FE, through…