PhysicsThe following truss is subjected to a load of P = 31 kN at joint C. The pin at joint A has a diameter of 25mm and is subjected to double shear. Determine the average shear stress developed in pin A of thetruss.ImPRNImPin Aa. In your Hard Copy, draw a FBD of the truss.b. What is the Resultant force at A?Aresultant = NumberUnits(Answer to 3 sig digs)c. What is the shear stress in A?TA = NumberUnits(Answer to 3 sig digs

Consider the diagram as shown below.

föllowing SS is subjected to diameter mm and is subjected to double shear. Determine the average shear stress developed in pin A of the truss. Im PAN Pin A -2 m a. In your Hard Copy, draw a FBD of the truss. b. What is the Resultant force at A? Aresultant = Number Units (Answer to 3 sig digs) c. What is the shear stress in A? TA = Number Units (Answer to 3 sig digs

föllowing SS is subjected to diameter mm and is subjected to double shear. Determine the average shear stress developed in pin A of the truss. Im PAN Pin A -2 m a. In your Hard Copy, draw a FBD of the truss. b. What is the Resultant force at A? Aresultant = Number Units (Answer to 3 sig digs) c. What is the shear stress in A? TA = Number Units (Answer to 3 sig digs

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the maximum tensile bending stresses in the beam shown. LetP= %3D 19 Note Answer in whole number I = 100 × 106 mm4 P kN/m 2. NA 130 mm 6 m B = 4P 200 mm 2P kN 6-X= Am 4P : - GP
Problem 1 A truss is subjected to the loadings as shown in the figure. Determine the force at member JI, IC, CD, and DI. Use combined solution using Method of Section and Method of Joints. State wether the force is Tension or Compression. USE 3 DECIMAL ONLY. 10 m, 5 @ 2 m 3 kN 6 kN 4 kN 3 kN 1.5 kN K Jooo o foo 00 F 5 m 9 kN B A Figure 1.0
Determine the maximum compressive bending stresses in the beam shown. Let P = 14 Note Answer in whole number I = 100 × 106 mm P kN/m 2. 130 mm A NA- B |= 4P 6 m Poy= 200 mm 2P kN 6 -X= 4m - 4P - GP
Determine the maximum tensile and compressive bending stresses developed in the beam shown. The cross-section has the given properties. NA 1-35 x 10mm a. RA = b. RE= c. fb(c) = d. fb(T) = 80 mm 200 mm A 1.5m kN KN 5kN m MPa MPa B 1.5m SkN/m 2m 5KN n 2m 4
Q₁: Analyze the truss shown below B с <50k 3m IMI A E 100ku EA is Constant for all members + Am X Am
A:Y 211O 2_531929016114... -> A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm, determine the stress in each section. 4P Steel Bronze |Aluminum 609.6 mm 914.4 mm 762 mm
Method of Joints Solve for the member forces in the truss by the method of joints. Provide your answers in kN to one decimal place. Use the correct sign: positive is tension, negative is compression. H F 3 m A D B - 4 m 4 m 4 m 4 m 3 kN 3 kN 4 kN 1) What is the force in member BH? 2) What is the force in member BC? 3) What is the force in member CG? 4) What is the force in member DE?
Problem 3: Method of Sections The structure shown is made of many weightless, solid and rigid members pinned together at different joints. The whole structure is pinned to the floor at point I and supported by a roller at point J. Two loads (F = 1N) are applied on the structure at points A and B. T A 1F 1L On the diagram, indicate where you cut the structure, in 1F C order to find the force in member GH. 1L About which point will you find the torque? (D E 1L Write the equation of the torque about your chosen axis. 3L
The members of the truss are 25mmx50mm in cross section. Determine the maximum load P that can be applied so that the stresses will not exceed 100 MPa in tension or 70 MPa in compression. See figure 101. Figure 101 A 0 2m P B 2.5m 1.5m C
Find the force in each member of the truss by using: 1- The method of consistent deformations. 2- Castigliano's second method. Take the member AB as a redundant. The stiffness EA is constant. 1,2 m ID 0.9 m 10 kN 0.9 m
Determine the magnitude of the pin force at A. Assume W = 645 Ib, a = 3.7 ft, b = 3.0 ft, r = 8 in. a - a r C B A W D Answer:A = i Ib
The truss is subjected to the loading shown. It is supported by a pin at A and a roller at L. Determine the force in members FH, HG and GI, and state if the members are in tension or compression. Present a FBD for every analysis performed. 2.4 kips 0.8 kip 1.6 kips B с 1.6 kips 8 ft D E 8 ft F G 8 ft 1.6 kips 8 ft H 1.6 kips 8 ft J K 0.8 kip obdo 8 ft 6 ft L 14.5 ft