Determine the discharge and compute the power consumption.(Neglect all minor losses.)AQHPeff.PUMP4₁D = 0.20 mf = 0.020L = L₁ + L₂ = kL₂PUMP CHARACTERISTICS0,010 0,0050,015 0,02 0,025 -0,0312 11.90 11.60 11.20 10.60 10.10 9,400,750,78 0,80 0,81 0,82k+5Bk=100,035 0,04 0,0458,60 7,80 7,100,83 0.830.82

Determine the discharge and compute the power consumption. (Neglect all minor losses.) A Q eff PUMP 4 12 0 0,005 0.01 11.90 11.60 0,75 D = 0.20 m f = 0.020 L=L₂ + L₂ = k L₂ PUMP CHARACTERISTICS 0,015 0,02 0,025 0.03 0,035 0,04 11.20 10.60 10.10 9,40 8.60 0.82 0.83 7,80 0.78 0.80 0,81 0.83 k+5 B K=10 0,045 2,10 0,82

Determine the discharge and compute the power consumption. (Neglect all minor losses.) A Q eff PUMP 4 12 0 0,005 0.01 11.90 11.60 0,75 D = 0.20 m f = 0.020 L=L₂ + L₂ = k L₂ PUMP CHARACTERISTICS 0,015 0,02 0,025 0.03 0,035 0,04 11.20 10.60 10.10 9,40 8.60 0.82 0.83 7,80 0.78 0.80 0,81 0.83 k+5 B K=10 0,045 2,10 0,82

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter12: Electric Current And Related Variables In Engineering

Section: Chapter Questions

Problem 23P

See similar textbooks

Similar questions

Reservoir B in the figure receives 0.06 m³/s of flow. Determine the flow in line DC. Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: m2/s Decimal Places required in the final answer: 3 El 100m A B 1500 m, 450 mm, f= 0.0225 El 82m 500 m, 250 mm f= 0.0178 D 750 m, 300 mm, f 0.0168
Q5: As shown in figure (5). What is the water horsepower of the pump? The pipes characteristics are as follows. Pipe 1 2 3 EL.0.0m D (mm) 200 300 250 L (m) 900 300 1500 0.135 m²/sec f 0.023 0.018 0.02 EL 120m EL.30m
14-41. The pipe system consists of a 3-in.-diameter, 100-ft- long galvanized iron pipe, a fully opened gate valve, four elbows, a flush entrance, and a pump with the pump head curve shown. If the friction factor is ƒ = 0.022, estimate the flow and corresponding pump head generated by the pump. 18 ft An () 160 140 120 100 80 60 40 20 50 100 150 200250300 350 400450 500 Le pal/min
Orange JO l M O ☆ O N 94 |14 4:40 Hydraulic-2018_.. 0.915 04. A tank is constructed of a series of cylinders as/ shown in the figure. The tank contains: oil p,915 kg/m, water p 1000 kg/m', glycerin p,= 1300 A3 kg/m, mercury p-13600 kg/m'. A mercury manometer is attached to the bottom of the tank Calculate the manometer reading h oil water mercury P-P ig +8, Xo-+ 8 Xo. +8 i X - 8 xhm 13.6x9S1o xhm + 13 x96o Xo. + 981o Xo + 0.915 X0.1 - 13.6 x 9 s10 Xhm 131416 x h + 1275.3 + 981 13341 6Xhm + 0.0915 133416 Xhm 2256.4 %3D 13416 x hm
Question 2 Oil (SG = 0.85) is flowing in a 10cm diameter pipe. The elevation of the pipe is 5m above the datum line and the pressure in the pipe is -24KP.. If the discharge in the pipe is 30 L/s, determine the power (in watts) in the stream at that point. A 843.17 Watts B 648.28 Watts (c) 926.41 Watts D No answer among the choices E 716.69 Watts
A 10-cm fire hose with a 3-cm nozzle discharges 1.5 m3/min to the atmosphere. Assuming frictionless flow, find the force FB exterted by the flange bolts to hold the nozzle on the hose. O 2728 N O5861 N Water: 1000 kg/m³ O 3566 N O 4067 N D₁ = 10 cm Pa = 0 (gage) Hint: One-dimensional momentum flux: F = ploutvout - Plin Vin (2) D₂ = 3 cm CV
(67) The water tank shown is filled by pumping water from the well where the water level is located 9 feet below the elevation of the pump. The head added by the pump at a flow rate of 200 gpm is 27 feet. The efficiency of the pump is 85%. The pump power (hp) is most nearly: A. 1.0 В. 1.5 C. 2.0 Tank D. 2.5 15 ft. Pump 9 ft. Well
Pump BC shown brings oil (SG = 0.72) to reservoir D at 170 L/sec. The energy lost from A to B is 1.1 J/N and from C to D is 4.7 J/N. El. 84 m D EL 22.6 m A 0.30-m Ø B El. 2.8m How many hp does the pump supply the system? O 108.164 hp O 112.069 hp O 150.228 hp O 80.690 hp
7- a) b) c) d) For the transmission line shown below, what is the power of the pump with efficiency of 70% to deliver 200 lit/s of water (y=9806 N/m³) from point I to point 4 if the slope of hydraulic grad line is: J=hi/L=3.66 x 10³ m/m. 30 m P 84.5 KW 102.46 kW 90.53 KW 89.22 KW Leave blank L = 1000 m 2 180 m L = 1000 m 3 L = 1300 m 105 m 320 m
200mmø 690mm 300 mm 400 mmø 金Ho0 Z Hg (13.6) A 200mm diameter venturi meter is installed in a 400mm diameter vertical main pipe as shown. If the deflection of mercury (SG = 13.6) at the manometer reads 300mm and the vertical distance between point 1 and point 2 is 690mm, determine the discharge in the system assuming a head loss of 600mm.
Q2- Water ( p= 990 kg/m' & µ= 0.001 pa.s) is pumping from a water tank to water injection well with carbon steel pipe at the same level, where the pipe diameter is 12 inch, pipe length is 4700 m, pipe roughness is 0.0000045 m, and water flow rate is 0.0065 m/sec. 1- Calculate discharge frictional head loss. 2- Calculate pump liquid power, if pump section head value is 3.8 m.
M MEQ2.jpg 200mmø 690mm 300 mm 400 mmø Z Hg (13.6) A 200mm diameter venturi meter is installed in a 400mm diameter vertical main pipe as shown. If the deflection of mercury (SG = 13.6) at the manometer reads 300mm and the vertical distance between point 1 and point 2 is 690mm, determine the discharge in the system assuming a head loss of 600mm. Hide answer choices a A) 307.36 L/s B) 279.84 L/s No Answer among the choices D) 224.67 L/s 256.29 L/s O O O O C