Determine the additional longitudinal reinforcements (mm?) due to torsion of a rectangular beam with a width of 469 mm and an over-all depth of 632 mm. It is subjected to a factored torsion of 110 kN-m. The specified compressive strength of concrete is 21.70 MPa. The yield strength of tension reinforcements and stirrups are 348 MPa and 278 MPa respectively. Use 12 mm stirrups. Round off only on your final answer (3 decimal places).

Determine the additional longitudinal reinforcements (mm?) due to torsion of a rectangular beam with a width of 469 mm and an over-all depth of 632 mm. It is subjected to a factored torsion of 110 kN-m. The specified compressive strength of concrete is 21.70 MPa. The yield strength of tension reinforcements and stirrups are 348 MPa and 278 MPa respectively. Use 12 mm stirrups. Round off only on your final answer (3 decimal places).

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The concrete post is reinforced axially with four symmetrically placed steel bars, each of cross-sectional area 900 mm2. Compute the stress in each material when the 1000-kN axial load is applied. The moduli of elasticity are 200 GPa for steel and 14 GPa for concrete. Compatibiltiy Equation . Ust Bearing |1000 kN plate Steel- Concrete 300 mm 300 mm Section a-a
A spiral column with the diameter of 500 mm has the effective height of lo-4.0 m. The axial compressive strength of the concrete is f. = 14.3 N/ mm. The longitudinal steel bars are 6 22 with the yield strength of fy = 360 N/mm. The spirals are d 10@50 with the yield strength of fy = 270 N/ mm. If the concrete cover is 30 mm thick, determine the ultimate compressive capacity of the column.
The end block of a post-tensioned beam is 100 mm x 150 mm. A prestressing cable consisting of 7 wires of 6 mm dia strand and stressed to 800 MPa has to be anchored at the center of the block. The anchorage plate is 75 mm x 75 mm. If the concrete mix is M45 and the permissible bending stress in M. S. steel plate is 165 MPa, determine the thickness of the anchorage plate.
A beam having a width of 500 mm and a total depth of 800mm is reinforced with 6-32mm dia bars, Compressive strength of concrete is 28 MPa and yield strength of reinforcing bars is 420MP.. 640 mm 800 mm 6 #32 80 mm 80 mm Determine the following: 1. depth of the compression block 2. strain in the tension reinforcement 3. moment reduction factor 4. nominal moment capacity 5. ultimate moment capacity 6. actual steel ratio 7. minimum steel ratio 8. maximum steel ratio 9. Tension force 10. Compression force
Determine the required tension steel area of the T beam with given properties below. Width of flange bf = 500 mm Width of web bw = 340 mm Thickness of flange tf = 140 mm Effective depth d = 350mm Effective concretee covering d' = 75mm Compressive strength of concrete fc' = 34.5 MPa Yield stress of steel bar fy = 375 MPa Mu = 415 kN-m As = _________ mm2
A beam having a width of 500 mm and a total depth of 800mm is reinforced with 6-32mm dia bars. Compressive strength of concrete is 28 MPa and yield strength of reinforcing bars is 420MPA. 640 mm 800 mm 6 #32 C 80 mm 80 mm Determine the following: 1. depth of the compression block 2. strain in the tension reinforcement 3. moment reduction factor 4. nominal moment capacity 5. ultimate moment capacity 6. actual steel ratio 7. minimum steel ratio 8. maximum steel ratio 9. Tension force 10. Compression force
A. Calculate the stress in the concrete at the top and bottom extreme fibers under a positive bending moment of 78 kip, in psi (neglect steel reinforcement) B. If fc= 3200 psi and normal weight of concrete is used, does cracking occurs? What is the maximum uniformly distributed load the beam can carry if it is used as a simple beam with a 26 ft span without exceeding the modulus of rupture of the concrete, in lb/ft? 250 mm 80 mm 130 mm 80 mm 80 mm
Figure 2 shows a simply supported beam and the cross section at midspan. The beam supports a uniform service (unfactored) dead load consisting of its own weight plus 1.4 kips/ft and a uniform service (unfactored) live load of 1.5 kips/ft. The concrete strength is 3500 psi, and the yield strength of the reinforcement is 60,000 psi. The concrete is normal-weight concrete. Use load (Table 5.3.1) and strength reduction factors from AC1318-14. For the midspan section shown in Fig. P4-1b, compute Mn and show that it exceeds Mu. @ (b) 3 No. 9 bars WD = 1.4 kips/ft plus weight of beam 1.5 kips/ft WL H 12 in. 20 ft TT 21.5 in. 24 in. + Figure 2.
7. Given a beam section b× D = 450 mm x 950 mm, M* = 1500 kNm, f=32 MPa, fy= 500 MPa and the maximum aggregate size = 20 mm. Design and detail the section. Use N28 bars for the main reinforcement and R10 bars for stirrups. Exposure clas- sification A2 applies.
A doubly reinforced concrete beam of size 250 mm x 500 mm overall depth is reinforced with 2-12 mm dia. bars in compression zone and 3-20 mm dia. bars in tension zone, each at an effective cover of 40 mm. The grade of concrete and steel are M20 and Fe415 respectively. The strain in compression steel will be [Take stress in compression steel as 345 MPa]
A rectangular beam has a width of 254mm and an effective depth of 600mm. It is reinforced with 4-36mm bars. The compressive strength of the concrete is 28MPa and the yield strength of the steel is 308MPa. The depth of the concrete stress block is ___ mm.
2. Tensile strength of concrete is about: (20-35)% of compressive strength (45-70)% of compressive strength None of the above. Tension controlled section Balanced section Compression-controlled section 4- The reduction factor (0) is equal to 0.9 if the: Es 2 Ety + 0.003 Es S Ety + 0.003 Es Ety 5- The design method which use the factored loads is - Working stress method - Ultimate design Method - None of above 6- If p< Po therefore the section is - Under reinforced - Over reinforced - None of above