R VTL Bistable (a) L+ VTH L_ V₁ ひっ V₂ D 15.46 Design the circuit in Fig. 15.24(a) to obtain symmetrical triangular and square waveforms of 10-kHz frequency. Use the circuit in Fig. 15.22(a) to implement the bistable. Assume that the op amps saturate at +5 V. The triangular waveform is required to have 2-V peak-to-peak amplitude. Use C = 1 nF and specify the values of the resistors.

R VTL Bistable (a) L+ VTH L_ V₁ ひっ V₂ D 15.46 Design the circuit in Fig. 15.24(a) to obtain symmetrical triangular and square waveforms of 10-kHz frequency. Use the circuit in Fig. 15.22(a) to implement the bistable. Assume that the op amps saturate at +5 V. The triangular waveform is required to have 2-V peak-to-peak amplitude. Use C = 1 nF and specify the values of the resistors.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Determine the required values of R1, R2, Rc, and RE. Also, determine the expected output voltage if the input voltage is equal to 0.001 Vrms. GIVEN: Zi = 1145.66 ohms Zo = 3.3 Kohms Beta = 80 Vcc = 20V R1 + R2 = 43.7 Kohms Av = 167.43 Ai = 58.13
Find the digital equivalent and the resolution for a 3 bit DAC using Successive Approximation of Vin = 0.7 V and Vref = 1 V?
Draw FM Modulator and demodulator the equation explain your answer by deriving at output
G) build a low-frequency square wave generator using a basic comparator having a frequency of 1kHz and a 30% duty cycle. Explain the principle of operation and the type of feedback of the op-amp. What is the advantage of this circuit? H) Build a phase-shift oscillator using, C=1µF and +10V power supply to produce a 10 kHz sinusoidal waveform. Generate your plots and compare output results. Highlight any discrepancies and discuss what happens if we want to increase the frequency to 100 kHz. I) Build a Colpitts oscillator producing 100kHz Discuss its advantage over RC oscillators. How can you modify the circuit to include a crystal in your circuit? What is a typical application of such an oscillator? Discuss the advantages and disadvantages of crystal oscillators.
For the Op - Amp circuit shown below, determine the output voltage V.. Show the details of your work. Write your solution on a white typewriting paper, scan it in JPEG format and upload it on the space provided below. 15V -15V V - 2.25 mV 750 kn 300 ka 20 kl 160 N
Thermistor giving output of 0.5 mv for each degree change in temperature. Find the word length required when its output passes through Analog to digital converter if temperature from 0 to 200 degree Celsius are to be measured with a resolution of 0.5 degree Celsius.
Project # 3 (Use a FET op-amp) You’ve been working with an implementation team to build the following components of a system: The system consists of a DC power supply, filters, instrumentation amplifier, one-state system and A/D converter.  Build an AC/DC dual power supply circuit that draws a 55Vp-p sinusoidal voltage, to provide a dc output voltage of +10 V. Find the proper data sheet of the IC regulator and specify ranges of output current and voltage. Full analysis of voltages and currents should be included. What modifications would you recommend to draw more current while maintaining same output voltage?  Build a 4th order Butterworth LP filters that cover a signal range 10kHz and a gain of 100V/V each. Use C = 0.01µF with proper values of R’s. Record your findings and include plots (magnitude and phase. Calculate the roll-off of the filter.  Build an instrumentation amplifier having a differential gain of 50V/V. Choose the right differential input and common input signals to…
v(t) 20V Vout -20V A laptop charger is connected with a load resistance R=37942 and practical PN junction diode is used as shown in Figure. Find the value of the output voltage in the positive half cycle (in volts) if the input applied voltage is v(t)=20sin314t.
Given is the buck-boost(Cuk) converter with the following data: Input voltage Vg = 42 V Output voltage V = 24 V Switching frequency fş = 200 kHz Load resistance R = 10 Q a. Determine, D,V₁, V₂, 1₁, and 1₂ b. sketch the inductor voltage and capacitor current waveforms indicating time and magnitude values. c. Determine the value of L₁,L₂, and C, so that Al₁ =1.2% of I₁, Al₂ -3% of 1₂ and Av₁ = 2% of Vg. d. Sketch i(t), 1₂. (t) and v₁ (t) V₂ 4₁ L₁ m C₁ 11 L, ron į₂ C₂ HH 1/2 R
CE Amp with pnp transistor VEE = 12V RE 13K2 prp B=l00 R2 look CE VA = O0 %3D Ri : G Rout (ka C2 RIN 300k2 Re RL Vo 43 k2 43k2 Find : 6) Av 6) RIN G) Rout d) max Vi to avoid small signal distortion ) max Vi to awidgoutput noltage ongadistarihim clipping in the
Silter power supply Co Load Hgure tleurly shows that a filter circuit is needed after the rectifier Cn cuit. A filter crcuit show that onverts Is called the action of filter circuit he AC power line voltuge to the required DC value in detail step by step thee the out put of the cilcuit load. Describe on filter power ( Load Supply
4. Consider the RC circuit in Figure 1.4. Let us consider a system whose input is the input voltage vin (t) and the output is the voltage across the capacitor vout (t). Find an integral equation that relates the input and output signals. Draw a block diagram showing a different realization (implementation) of this system using integrators, multipliers and adders.